|
IK Semiconductor |
m TECHNICAL DATA
T P heeAt4U.co CRIAC HASE NGLE ONTROLLER
ILA1185A
taSThe ILA1185A generates controlled triac triggering pulses and allows tachless speed stabilization of universal motors
aby an integrated positive feedback function. Typical applications are power hand tools, vacuum cleaners, mixers, light
.Ddimmer and other small appliances.
ww• Supply Power Obtained from AC Line
w• Can be used with 220 V/50 Hz or 110 V/60 Hz
• Low Count/Cost External Components
• Optimum Triac Firing (2nd and 3rd Quadrants)
• Repetitive Trigger Pulses when Triac Current is
mInterrupted
by Motor Brush Bounce
o• Triac Current Sensing to Allow Inductive Loads
.c• Programmable Soft-Start
• Power Failure Detection and General Circuit Reset
• Low Power Consumption; 6.0 mA
www.DataSheet4UFigure 1. Representative Block Diagram
Pin Connection
1VEE
Gate trigger 2
NC 3
Ramp Generator 4
NC 5
Current Cense 6
Voltage Cense 7
14 VCC
13 Soft start
12 Finning Angle Set
11 NC
10 Bias Current
9 Feedback Input
8 Integration Cap
www.DataSheet4U.com
1
ILA1185A
MAXIMUM RATINGS (voltages are referenced to Pin 14 (ground) unless other noted)
Rating
Maximum Voltage Range per Listed Pin Pins3. 5,11 (not
connected)
Pins 4,8.13
Pin 2
Maximum Positive Voltage (No minimum value allowed;
see current ratings)
Maximum Current per Listed pin
Pin 1
Pin 6 and 7
Рin 9
Pin 10
Pin12
Maximum Power Dissipation (ТA=25oС)
Maximum Thermal Resistance, .Junction-to-Ambient
Operating Ambient Temperature Range
Storage Temperature Range
Symbol
Vpin
Vpin12
Vpin1
Ipin
PD
RθJA
TA
Tstg
Value
Unit
-20 to+20
-VCC to 0
-3.0 to +3.0
0
0.5
±20
±2.0
±0.5
±300
-500
250
100
0 to + 70
-55 to <+ 125
V
mA
mA
mA
µA
µA
mW
oC/W
oC
oC
ELECTRICAL CHARACTERISTICS (ТA= 25°С, voltages are referenced to Pin 14 (ground) unless other
noted.)
Characteristics
Power Supply
Zener Regulated Voltage,
(Vpin1) Ipin1= 2.0 mA
Circuit Current Consumption. Ipin1
Vpin1=-6,0V,Ipin2=0A
Monitoring Enable Supply Voltage (VEN)
Monitoring Disable Supply Voltage (VDIS)
Phase Set
Control Voltage Static Offset Vpin3 – Vpin12
Pin 12 Input Bias Current
Vpin4 – Vpin12 Residual Offset
Soft-Start Capacitor Charging Current
Rpin10 = 100 kΩ Vpin13 from -Vcc to - 3.0V
Sawtooth Generator
Sawtooth Capacitor Discharge Current
R10=100 kΩ, Vpin4 from -2.0 to -6.0V
Capacitor Charging Current
Sawtooth -High Voltage (Vpin 4)
Sawtooth Minimum Low Voltage (Vpin4)
Symbol
Min
Typ Мax Unit
-VCC
-ICC
Vpin1EN
Vpin1DIS
Voff
Ipin12
lpin13
-9.6
-2.0
VCC+0.2
VEN+0.12
1.2
-200
-
-17'
-8.6 -7.6
-1.0 -
VCC+0.5
VEN+0.3
- 2.0
-0
180 -
-14 -11
V
mA
V
V
nА
mV
µA
lpin4
lpin4
VHTH
VLTH
67 70 73 µA
-10 - -1.5 mA
-2.5 -1.6 -1.0
V.
- -7.1 -
V
2
|