|
Sipex |
®
SP332
RS-232/RS-485 Multi-Mode Serial Transceiver
s +5V-Only Single Supply Operation
s 4 Drivers, 4 Receivers RS-232
s 2 Drivers, 2 Receivers RS-485
s Loop Back Function for Self Test
s 28 Pin SOIC Packaging
DESCRIPTION…
The SP332 is a monolithic device that contains both RS-232 and RS-485 line drivers and
receivers. The configuration of the SP332 can be changed at any time by changing the logic
state of two control input pins. The device also includes a loop back function which internally
connects driver outputs to receiver inputs for a chip self test. A Sipex-patented charge pump
(5,306,954) allows +5V-only operation.
RS-232 Mode
+5V
0.1µF
0.1µF
0V
0V
TTL/CMOS
TTL/CMOS
TTL/CMOS
TTL/CMOS
9 C1+
5
VCC
12 C1-
11 C2+
SP332
10
V+
V- 14
13
C2-
24 SEL A
2 SEL B
Vcc
0.1µF
LOOP 23
BACK
400KΩ
26 TI1
T1
Vcc
TX1 6
400KΩ
27 TI2
T2
Vcc
TX2 7
400KΩ
28 TI3
Vcc
T3
TX3 4
400KΩ
1 TI4
T4
TX4 3
0.1µF
TTL/CMOS
RS-232
RS-232
RS-232
RS-232
TTL/CMOS
TTL/CMOS
TTL/CMOS
TTL/CMOS
19 RX1
20 RX2
21 RX3
22 RX4
8
GND
RI1 15
R1
5KΩ
RI2 16
R2
5KΩ
RI3 17
R3
5KΩ
RI4 18
R4
5KΩ
SHUT
DOWN
25
RS-232
RS-232
RS-232
RS-232
TTL/CMOS
Full Duplex RS-485
+5V
0.1µF
0.1µF
TTL/CM+5OVS
TTL/CM+5OVS
TTL/CMOS
TTL/CMOS
TTL/CMOS
TTL/CMOS
TTL/CMOS
TTL/CMOS
TTL/CMOS
TTL/CMOS
9 C1+
5
VCC
12 C1-
11 C2+
SP332
13
C2-
24
2 SEL A
SEL B
Vcc
26 TI1
T1
27 TI2 Vcc
28 TI3
1
TI4
19 RX1
20
RX2
T3
R1
21 RX3
R3
22 RX4
8 GND
10
V+
14
V-
0.1µF
LOOP 23
BACK
TX2 7
TX1 6
TX4 3
TX3 4
RI2 16
RI1 15
RI4 18
RI3 17
SHUT 25
DOWN
0.1µF
TTL/CMOS
RS-485/RS-232
RS-485/RS-232
RS-485/RS-232
RS-485/RS-232
RS-485/RS-232
RS-485/RS-232
RS-485/RS-232
RS-485/RS-232
TTL/CMOS
TGoddard/SP332/9617R0
SP332 RS-232/RS-485 Multi-Mode Serial Transceiver
1
© Copyright 2000 Sipex Corporation
ABSOLUTE MAXIMUM RATINGS
These are stress ratings only and functional operation of the device at
these ratings or any other above those indicated in the operation sections
of the specifications below is not implied. Exposure to absolute maximum
rating conditions for extended periods of time may affect reliability.
V ............................................................................................................+12V
CC
Input Voltages
Logic........................................................-0.5V to (VCC+0.5V)
Drivers..................................................-0.5V to (VCC+0.5V)
Receivers.................................................±30V@≤100mA
Driver Outputs......................................................................................±15V
Storage Temperature..................................................-65˚C to +150˚C
Power Dissipation..........................................................................1000mW
SPECIFICATIONS
TMIN to TMAX and VCC = 5V±5% unless otherwise noted.
PARAMETER
MIN.
RS-485 DRIVER
DC Characteristics
Differential Output Voltage GND
Differential Output Voltage
2.0
TYP.
MAX.
VCC
5.0
Differential Output Voltage
1.5
5.0
Change in Magnitude of Driver
Differential Output Voltage for
Complementary States
Driver Common-Mode Output
Voltage
Input High Voltage
2.0
0.2
3
Input Low Voltage
0.8
Input Current
Pull-Up Current
Pull-Down Current
Driver Short-Circuit
Current
VOUT= HIGH
VOUT= LOW
AC Characteristics
Driver Data Rate
Driver Input to Output
t
PLH
Driver Input to Output
tPHL
Driver Skew
±10
1.5
3.0
35 250
35 250
10
70 180
70 180
5 10
Driver Rise or Fall Time
3 15 40
RS-485 RECEIVER
DC Characteristics
Differential Input Threshold -0.2
+0.2
Input Hysteresis
70
Output Voltage High
3.5
Output Voltage Low
0.4
Input Resistance
12 15
Input Current (A, B); VIN= 12V
+1.5
Input Current (A, B); VIN= -7V
Short Circuit Current
-0.8
85
UNITS CONDITIONS
Volts
Volts
Volts
Unloaded; R=∞; see figure 1
With Load; R=50Ω (RS-422);
see figure 1
With Load; R=27Ω (RS-485);
see figure 1
Volts
Volts
Volts
Volts
µA
µA
µA
R=27Ω or R=50Ω; see figure 1
R=27Ω or R=50Ω; see figure 1
Applies to transmitter inputs,
SEL A, SEL B, SD, LB
Applies to
SEL A, SEL B, SD, LB
Applies to:
transmitter inputs, LB
SEL A, SEL B, SD,
mA -7V≤VO≤10V
mA -7V≤VO≤10V
Mbps
ns
ns
ns
ns
RDIFF=54Ω,
C =C =100pF;
L1 L2
see figures 3 and 6
RDIFF=54Ω, CL1=CL2=100pF;
see figures 3 and 6
From output to output;
see figures 3 and 6
From 10% to 90%; RDIFF=54Ω,
C =C =100pF; see figures 3 and 6
L1 L2
Volts
mV
Volts
Volts
kΩ
mA
mA
mA
-7V≤VCM≤12V
VCM=0V
IO=-4mA, VID=+200mV
I =+4mA, V =-200mV
O ID
-7V≤VCM≤12V
VIN= 12V, A is the non-inverting
receiver input. B is the inverting
receiver input
VIN= -7V
0V≤VCM≤VCC
TGoddard/SP332/9617R0
SP332 RS-232/RS-485 Multi-Mode Serial Transceiver
2
© Copyright 2000 Sipex Corporation
|