V23134-A0052-X278 반도체 회로 부품 판매점
Power Relay
|
|
 TE |
Automotive Relays
Plug-in Mini ISO Relays
Power Relay F4
n Pin assignment similar to ISO 7588 part 1
n Plug-in or PCB terminals
n Also available for 42VDC applications
Customized versions on request
– 24VDC versions with contact gap >0.8mm
– Integrated components (e.g. resistor, diode)
– Customized marking/color
– Special covers (e.g. notches, release features, brackets)
– Various contact arrangements and materials
– For latching (bistable) version refer to Power Relay F7 A Latching
or Mini Relay Latching
– For shrouded/weatherproof dust cover versions refer to
Shrouded Power Relay F4 A and VF4 A
Typical applications
Cross carline up to 40A for example: ABS control, blower fans, car alarm,
cooling fan, Electric Power Steering, energy management, engine control,
fuel pump, heated front screen, lamps: front, rear, fog light, main switch/
supply relay, valves, wiper control.
F134co_fcw1
Contact Data
Contact arrangement
1 form A, 1 NO/1 NO (2x87) 1 form U, 2 NO
1 form C, 1 CO
Contact gap
>0.8mm
Rated voltage
12VDC 24VDC
12VDC 24VDC
12VDC 24VDC 24VDC1)
Limiting continuous current
NO
NO
NO
NO
NO/NC
NO/NC
NO/NC
23°C
60A 60A
2x32A 2x32A
60/45A 60/45A 60/45A
85°C
40A 40A
2x25A 2x25A
40/30A 40/30A 40/30A
125°C
17A 17A
2x11A 2x11A
17/12A 17/12A 17/12A
Limiting making current2)
NO/NC
120A 120A
2x100A 2x100A
120/45A 120/45A 120/45A
Limiting breaking current
NO/NC
60A 20A
2x40A 2x15A
60/40A 20/15A 30/20A
Limiting short-time current
overload current, ISO 8820-33):
1.35 x 40A, 1800s 1.35 x 40A, 1800s 1.35 x 40A, 1800s
2.00 x 40A, 5s 2.00 x 40A, 5s
2.00 x 40A, 5s
3.50 x 40A, 0.5s 3.50 x 40A, 0.5s
3.50 x 40A, 0.5s
6.00 x 40A, 0.1s 6.00 x 40A, 0.1s
6.00 x 40A, 0.1s
Jump start test
ISO 16750-1 24VDC for 5min conducting nominal current at 23°C
Contact material silver based
Min. recommended contact load4) 1A at 5VDC
Initial voltage drop
NO contact at 10A, typ./max. 15/200mV 15/200mV
2x15/200mV 2x15/200mV
15/200mV 15/200mV 15/200mV
NC contact at 10A, typ./max.
20/250mV 20/250mV 20/250mV
Frequency of operation
at nominal load 6 ops./min (0.1Hz)
Operate/release time typ. 7/2ms5)
Electrical endurance
resistive load at 14VDC
>2x105 ops. >2x105 ops.
>2x105 ops.
40A
2x25A
40A (NO)
resistive load at 28VDC
>1x105 ops.
>1x105 ops.
>1x105 ops. 1x105 ops.
20A
2x15A
20A (NO) 30A (NO)
>5x105 ops.
10A (NC)
Mechanical endurance
DC coil >1x107ops.
1) Special high performance 24VDC version with contact gap >0.8mm, part number V23134-A0056-X432/-X433 (see part number table).
2) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 14VDC for 12VDC or 28VDC for 24VDC load voltages. For a load current duration of
maximum 3s for a make/break ratio of 1:10.
3) Current and time are compatible with circuit protection by a typical automotive fuse. Relay will make, carry and break the specified current.
4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/
5) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher
risk of contact tack welding.
11-2013, Rev. 1113
www.te.com
© 2013 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
1
Automotive Relays
Plug-in Mini ISO Relays
Power Relay F4 (Continued)
Max. load DC breaking capacity
6) Without components in parallel.
Insulation Data
Initial dielectric strength
between open contacts
between contact and coil
between adjacent contacts
Load dump test
ISO 7637-1 (12VDC), test pulse 5
ISO 7637-2 (24VDC), test pulse 5
500Vrms
500Vrms
500Vrms
Vs=+86.5VDC
Vs=+200VDC
Other Data
EU RoHS/ELV compliance
compliant
Ambient temperature DC coil
-40 to +125°C
Protection to heat and fire UL94-HB or better7)
Climatic cycling with condensation
EN ISO 6988 6 cycles, storage 8/16h
Temperature cycling
IEC 60068-2-14, Nb 10 cycles, -40/+85°C (5°C/min)
Load limit curve 1: arc extinguishes during transit time (CO contact).
Damp heat cyclic
Load limit curve 2: safe shutdown, no stationary arc (NO contact).
Load limit curves measured with low inductive resistors verified for 1000 switching events.
IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55°C
Damp heat constant
IEC 60068-2-3, Ca
56 days
Category of environmental protection,
IEC 61810 RTI – dustproof, RT III – sealed
Coil Data
Degree of protection, IEC 60529 IP54 (dustproof), IP67 (sealed)
Corrosive gas
Rated coil voltage
Coil versions, DC coil
12/24VDC
IEC 60068-2-42 10±2cm3/m3 SO2, 10 days
IEC 60068-2-43 1±0.3cm3/m3 H2S, 10 days
Vibration resistance (functional)
Coil
Rated
Operate Release
Coil Rated coil IEC 60068-2-6 (sine sweep) 10 to 500Hz > 5g8)
code voltage voltage voltage resistance6) power6)
Shock resistance (functional)
VDC VDC VDC Ω±10% W
IEC 60068-2-27 (half sine)
11ms >20g8)
052 12 7.2 1.6 90 1.6
Drop test, free fall
053 24 14.4 3.2 324 1.8
IEC 60068-2-32 1m onto concrete
056 24 16 4 268 2.1
Terminal type
plug-in, QC/PCB
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Coil operating range
Cover retention
axial force
150N
TE0701-J1
pull force
push force
150N
150N
Terminal retention
pull force
100N
push force
100N
resistance to bending, force applied to front9) 10N
resistance to bending, force applied to side9) 10N
torque
0.3Nm
DttEhho=eeetcspeoPW 7rnmne)aot-eRptacppeeiecgtnkllrafuuteeahakggcrrttgesugu --iririitniznnenroaegt/rtouwnPiisusotaCieentnchdBidctoum b ueranattteocrkiaelst.
approx. 35g (1.2oz)
315 pcs.
200 pcs.
8) No change in the switching state >10μs. Valid for NC contacts, NO contact values
significantly higher.
9) Values apply 2mm from the end of the terminal. When the force is removed, the terminal
must not have moved by more than 0.3mm.
Does not take into account the temperature rise due to the contact current E=pre-
energization..
Accessories
For details see datasheet Connectors for Mini ISO Relays
2
11-2013, Rev. 1113
www.te.com
© 2013 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
|
PDF 파일 내의 페이지 : 총 4 페이지
제조업체: TE
( te )
V23134-A0052-X278 relay
데이터시트 다운로드 :
[ V23134-A0052-X278.PDF ]
[ V23134-A0052-X278 다른 제조사 검색 ]
국내 전력반도체 판매점
상호 : 아이지 인터내셔날
전화번호 : 051-319-2877
[ 홈페이지 ]
IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈
( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )
전력반도체 문의 : 010-3582-2743
