|
ON Semiconductor |
NCP5426
LDO Regulator/Vibration
Motor Driver
The NCP5426 series of fixed output, 150 mA low dropout linear
regulators are designed to be an economical solution for a variety of
applications. Each device contains a voltage reference unit, an error
amplifier, a PNP power transistor, resistors for setting output voltage,
an under voltage lockout on the input, an enable pin, and current limit
and temperature limit protection circuits.
The NCP5426 is designed for driving a vibration motor using
ceramic capacitors on the output. The device is housed in the
micro−miniature TSOP−5 surface mount package. The NCP5426 is
available in output voltages of 1.2 V to 2.0 V in 0.1 V increments.
Features
• Wide Operating Voltage Range to 12 V
• Internally Set Output Voltages
• Enable Pin for On/Off Control
• UVLO on the Input Voltage with Hysteresis
• Current and Thermal Protection
• Compatible with Ceramic, Tantalum or Aluminum Electrolytic
Capacitors
• Pb−Free Package is Available
www.DataSheet4U.com
Typical Applications
• Vibration Motor Driver
Vin
5
UVLO
Thermal
Shutdown
Driver w/
Current
Limit
Enable
ON 1
Vout
4
OFF
GND 2
This device contains 47 active transistors.
Figure 1. Internal Schematic
http://onsemi.com
5
1
TSOP−5
SN SUFFIX
CASE 483
PIN CONNECTIONS AND
MARKING DIAGRAM
Enable 1
GND 2
5 Vin
N/C 3
4 Vout
(Top View)
xxx = Specific Device Code
A = Assembly Location
Y = Year
W = Work Week
G = Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 7 of this data sheet.
© Semiconductor Components Industries, LLC, 2006
February, 2006 − Rev. 5
1
Publication Order Number:
NCP5426/D
NCP5426
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁDETAILED PIN DESCRIPTION
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁPin Name
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ1 Enable
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ2 GND
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ3 N/C
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ4 Vout
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ5 Vin
Description
The enable pin allows the user to control the output. A low signal disables the output and places
the device into a low current standby mode.
Ground pin.
This pin is not connected to the device.
Regulated output voltage.
Input voltage.
MAXIMUM RATINGS
Rating
Max Voltage, All Pins
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁPower Dissipation to Air
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁPower Dissipation, Board Mounted
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁOperating and Storage Temperature
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁThermal Resistance
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁJunction Temperature
Symbol
VMAX
PA
P
TA
TJA
TJ
Value
12
150
600
−40 to 85
300
125
Unit
V
mW
mW
°C
°C/W
°C
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
ELECTRICAL CHARACTERISTICS (TA = 25°C, for min/max values TA is the operating junction temperature that
applies, VCC = 3.5 V, unless otherwise noted)
Characteristic
Symbol
Min Typ Max
Operating Voltage
VCC
− − 12
Operating Voltage Turn On, Iout = 30 mA, Increasing VCC
VCCON
− 2.6 2.8
Operating Voltage Turn Off, Iout = 30 mA, Decreasing VCC
VCCOFF
2.0 2.1 2.2
Operating Voltage Hysteresis, Iout = 30 mA
VCC(hyst)
400 500 600
Operating Current No Load
ICC − 120 240
Operating Current, VCC = 1.8 V, Enable High
ICC(uvlo)
− 80 160
Operating Current, Enable Low
ICC(off)
− − 0.1
Maximum Output Current, Vout = 0.95 *Vnom
Iout(max) 150 −
−
Overcurrent Protection, Vout = 0 V
Iout(limit)
− 270 −
Load Regulation, Vin = 3.5 V, Iout 1.0 to 100 mA
Regload
− 30 60
Line Regulation, Iout = 30 mA, Vin 3.0 to 5.0 V
Regline
− 10 20
Ripple Rejection, Vin 3.5 V, f 120 Hz, Vpp 1.0 V, Iout 30 mA
RR
55 70
−
Temperature Shutdown
Tstd − 150 −
VCC Low Detector Temperature Coefficient, Iout = 30 mA,
DVCC H to L/DT
−
200
−
T = −40 to 85°C
Vout Temperature Coefficient
Enable Pin High Threshold
Enable Pin Low Threshold
Enable Pin Current, Ve = 1.6 V
−1.3 V
DVo/DT
Veh
Vel
le
− 100 −
1.6 −
−
− − 0.4
− 5.0 10
Output Voltage, Iout = 30 mA
Vout 1.261 1.3 1.339
Unit
V
V
V
mV
mA
mA
mA
mA
mA
mV
mV
dB
°C
ppm/°C
ppm/°C
V
V
mA
V
http://onsemi.com
2
|