RX5000 반도체 회로 부품 판매점
433.92 MHz Hybrid Receiver
|
|
 RF Monolithics Inc |
®
· Designed for Short-Range Wireless Control and Data Communications
· Supports RF Data Transmission Rates Up to 115.2 kbps
· 3 V, Low Current Operation plus Sleep Mode
· Stable, Easy to Use, Low External Parts Count
The RX5000 hybrid receiver is ideal for short-range wireless control and data applications where
robust operation, small size, low power consumption and low cost are required. The RX5000
employs RFM’s amplifier-sequenced hybrid (ASH) architecture to achieve this unique blend of
characteristics. All critical RF functions are contained in the hybrid, simplifying and speeding de-
sign-in. The RX5000 is sensitive and stable. A wide dynamic range log detector, in combination
with digital AGC and a compound data slicer, provide robust performance in the presence of
on-channel interference or noise. Two stages of SAW filtering provide excellent receiver out-
of-band rejection. The RX5000 generates virtually no RF emissions, facilitating compliance with
ETSI I-ETS 300 220 and similar regulations.
RX5000
433.92 MHz
Hybrid
Receiver
Absolute Maximum Ratings
Rating
Power Supply and All Input/Output Pins
Non-Operating Case Temperature
Soldering Temperature (10 seconds)
Value
-0.3 to +4.0
-50 to +100
250
Units
V
oC
oC
Electrical Characteristics (typical values given for 3.0 Vdc power supply, 25 oC)
Characteristic
Sym Notes
Operating Frequency
Modulation Type
fO
Data Rate
Receiver Performance, High Sensitivity Mode
Sensitivity, 2.4 kbps, 10-3 BER, AM Test Method
1
Sensitivity, 2.4 kbps, 10-3 BER, Pulse Test Method
1
Current, 2.4 kbps (RPR = 330 K)
Sensitivity, 19.2 kbps, 10-3 BER, AM Test Method
2
1
Sensitivity, 19.2 kbps, 10-3 BER, Pulse Test Method
1
Current, 19.2 kbps (RPR = 330 K)
Sensitivity, 115.2 kbps, 10-3 BER, AM Test Method
2
1
Sensitivity, 115.2 kbps, 10-3 BER, Pulse Test Method
1
Current, 115.2 kbps
Receiver Performance, Low Current Mode
Sensitivity, 2.4 kbps, 10-3 BER, AM Test Method
1
Sensitivity, 2.4 kbps, 10-3 BER, Pulse Test Method
1
Current, 2.4 kbps (RPR = 1100 K)
2
Minimum
433.72
Typical
OOK/ASK
-109
-103
3.0
-105
-99
3.1
-101
-95
3.8
-104
-98
1.8
Maximum
434.12
115.2
Units
MHz
kbps
dBm
dBm
mA
dBm
dBm
mA
dBm
dBm
mA
dBm
dBm
mA
1
Electrical Characteristics (typical values given for 3.0 Vdc power supply, 25 oC)
Characteristic
Sym Notes
Receiver Out-of-Band Rejection, ±5% fO
Receiver Ultimate Rejection
Sleep Mode Current
Power Supply Voltage Range
Power Supply Voltage Ripple
R±5%
RULT
IS
VCC
3
3
Ambient Operating Temperature
TA
Minimum
2.2
-40
Typical
80
100
0.7
Maximum
3.7
10
85
Units
dB
dB
µA
Vdc
mVP-P
oC
Notes:
1. Typical sensitivity data is based on a 10-3 bit error rate (BER), using DC-balanced data. There are two test methods commonly used to
measure OOK/ASK receiver sensitivity, the “100% AM” test method and the “Pulse” test method. Sensitivity data is given for both test meth-
ods. See Appendix 3.8 in the ASH Transceiver Designer’s Guide for the details of each test method, and for sensitivity curves for a 2.2 to
3.7 V supply voltage range at five operating temperatures. The application/test circuit and component values are shown on the next page and
in the Designer’s Guide.
2. At low data rates it is possible to adjust the ASH pulse generator to trade-off some receiver sensitivity for lower operating current. Sensitiv-
ity data and receiver current are given at 2.4 kbps for both high sensitivity operation (RPR = 330 K) and low current operation (RPR = 1100 K).
3. Data is given with the ASH radio matched to a 50 ohm load. Matching component values are given on the next page.
4. See Table 1 on Page 8 for additional information on ASH radio event timing.
S M -2 0 L P a c k a g e D r a w in g
0 .3 8 "
(9 .6 5 )
0 .0 8 "
(2 .0 3 )
0 .4 3 "
(1 0 .9 )
0 .1 2 5 "
(3 .2 0 )
0 .0 2 "
(0 .5 1 )
0 .0 4 "
(1 .0 2 )
0 .1 3 "
(3 .3 0 )
0 .0 7 5 "
(1 .9 0 )
A S H T r a n s c e iv e r P in O u t
GND1
VCC1 2
AG CCAP 3
PKDET 4
BBO UT 5
C M P IN 6
R XD ATA 7
TXM O D 8
LP FA D J 9
GND2
1 20
10 11
R F IO
19 G N D 3
18 C N TR L0
17 C N TR L1
16 V C C 2
1 5 P W ID T H
14 P R A TE
13 TH LD 1
12 TH LD 2
RREF
2
|
PDF 파일 내의 페이지 : 총 11 페이지
제조업체: RF Monolithics Inc
( rfm )
RX5000 receiver
데이터시트 다운로드 :
[ RX5000.PDF ]
[ RX5000 다른 제조사 검색 ]
국내 전력반도체 판매점
상호 : 아이지 인터내셔날
전화번호 : 051-319-2877
[ 홈페이지 ]
IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈
( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )
전력반도체 문의 : 010-3582-2743
관련 데이터시트
RX5000
433.92 MHz Hybrid Receiver - RF Monolithics Inc
RX5003
303.825 MHz Hybrid Receiver - RF Monolithics Inc