|
Integrated Circuit Systems |
Integrated Circuit Systems
M655 Series
Performance Specifications
M655 Series
Voltage Controlled SAW Oscillators
DESCRIPTION
9mm
14mm
FEATURES
Output Frequencies at 155MHz to
900MHz
Low Phase Jitter, 0.5psec (rms) typical
3.3 Volt Supply Operation
Complementary Outputs
Output Disable Feature
LCC Surface Mount Package
(9 x 14mm)
The M655 Series of Voltage Controlled SAW
Oscillators is a low cost solution for many Telecom
applications. An internal SAW filter provides jitter
performance of less than 0.5psec (rms).
This device is specified for an operating
temperature range of -40°C to +85°C. A disable
feature forces the output into a static condition by
applying a logic “0” to the clock enable input. The
oscillator is housed in a hermetically-sealed,
leadless surface mount package.
The M655 Series of VCOs is available over an
output frequency range of 155MHz to 900MHz.
The device is most suited for phase-locked loop
applications as well as clock and data recovery
circuits.
APPLICATION
Clock Smoothing for OC192/OC48/
OC12/OC3
Clock Smoothing for STS96/STS48/
STS12/STS3/STS1
Frequency Translation
Clock and Data Retiming
ABSOLUTE MAX RATINGS
Operating Temp. Range (Case): ........................ -40°C to +85°C
Storage Temp. Range (Ambient): .................... -55°C to +125°C
Control Voltage Range: ................................................. 0 to VCC
Output Current: ................................................................ 20 mA
Power Supply Voltage (Vcc): ................................ 0 to +3.6 Vdc
Integrated Circuit Systems, Inc.
Communications Modules
1
www.icst.com/Comm-Modules
ISO 9001
Registered
tel: 508-852-5400
Integrated Circuit Systems
M655 Series
Performance Specifications
SPECIFICATIONS
Specifications @ Vcc = +3.3 Volts, Vee = 0 Volts, and Ta = +25°C unless otherwise specified
PARAMETER
Min Typ
Output Frequency
Absolute Pull Range
Frequency Stability (-40°C to 85°C)
Duty Cycle
Spurious Suppression-50
Linearity
Logic Levels
Vol1
Voh2
Input Control Voltage (Vc) Range
VCO Gain
Vc Input Impedance
Vc Modulation BW
Clock/Output Enable (Pin 2)
Clock/Output Disable (Pin 2)
Output Rise Time
Output Fall Time
Jitter @ 155.520MHz offset from carrier
12kHz to 20MHz
Jitter @ 622.080MHz offset from carrier
12kHz to 80MHz
Phase Noise (offset from carrier)
100Hz
1kHz
10kHz
100kHz
Operating Temperature
Supply Current Icc
Supply Voltage
Vcc
155
±50
45
-60
Vcc - 1.95
Vcc - 0.98
0
8
2.0
-0.3
-40
3.2
+25/-150
±6
200
500
250
250
0.230
0.458
-65
-95
-120
-140
25
80
3.3
Notes: 1. Output levels are standard 10K ECL and are fully 100K ECL compatible.
2. Transition times are measured from 20% to 80% of a full 10K ECL level swing.
Max
900
55
dBc
Vcc - 1.63
Vcc - 0.75
Vcc
12
Vcc +0.3
0.8
400
400
+85
95
3.4
Units
MHz
ppm
ppm
%
%
Volts
Volts
Volts
ppm/V
KΩ
kHz
Volts
Volts
psec
psec
psec rms
psec rms
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
°C
mA
V
Phase Noise
-90
-100
-110
-120
-130
-140
-150
-160
-170
1E+03
1E+04
1E+05
1E+0
Frequency in Hz
Integrated Circuit Systems, Inc. Communications Modules www.icst.com/Comm-Modules
2
tel: 508-852-5400
|