1008AF-112XKLB 반도체 회로 부품 판매점
Chip Inductors
|
|
 Coilcraft |
Document 578-1
Chip Inductors – 1008AF (2520)
• Lowest DCR and highest current rating of our 1008 size
inductors
• Available in 14 inductance values from 0.9 to 10 µH.
Request free evaluation samples by contacting Coilcraft
or visiting www.coilcraft.com.
Part number1
Inductance2
Percent
(µH)
tolerance3 Q typ4
SRF min5
DCR max6
Isat7
Irms8
(MHz) (Ohms) (A) (A)
1008AF-901X_L_ 0.9 10,5
1008AF-112X_L_ 1.1 10,5
1008AF-132X_L_ 1.3 10,5
1008AF-152X_L_ 1.5 10,5
1008AF-192X_L_ 1.9 10,5
1008AF-222X_L_ 2.2 10,5
1008AF-272X_L_ 2.7 10,5
1008AF-332X_L_ 3.3 10,5
1008AF-392X_L_ 3.9 10,5
1008AF-472X_L_ 4.7 10,5
1008AF-582X_L_ 5.8 10,5
1008AF-682X_L_ 6.8 10,5
1008AF-822X_L_ 8.2 10,5
1008AF-103X_L_ 10.0 10,5
25
24
37
22
29
21
22
21
21
27
21
20
20
22
415
376
198
135
126
106
70
59
55
48
37
33
34
26
0.100 1.4 1.3
0.105 1.3 1.2
0.110 1.2 1.1
0.125 1.1 1.0
0.140 1.0 1.0
0.155 0.95 0.95
0.190 0.80 0.90
0.210 0.75 0.80
0.220 0.70 0.80
0.435 0.70 0.65
0.280 0.55 0.75
0.315 0.50 0.70
0.395 0.50 0.65
0.480 0.45 0.55
1. When ordering, specify tolerance, termination and packaging codes:
1008AF-103XJLC
Tolerance: J = 5% K = 10%
(Table shows stock tolerances in bold.)
Termination: L = RoHS compliant silver-palladium-platinum-glass
frit. Special order: T = RoHS tin-silver-copper
(95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
D = 13″ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (7500 parts per
full reel).
2. Inductance measured at 2.5 MHz using Coilcraft SMD-A fixture in an
Agilent/HP 4286A impedance analyzer with Coilcraft-provided correla-
tion pieces.
3. Tolerances in bold are stocked for immediate shipment.
4. Q measured at 2.5 MHz using an Agilent/HP 4291A with an Agilent/HP
16193 test fixture.
5. SRF measured using an Agilent/HP 8753D network analyzer with a
Coilcraft SMD-D fixture.
6. DCR measured on a Cambridge Technology Micro-ohmmeter.
7. DC current at 25°C that causes an inductance drop of 10% (typ) from its
value without current. Click for temperature derating information.
8. Current that causes a 40°C temperature rise from 25°C ambient. This
information is for reference only and does not represent absolute maxi-
mum ratings. Click for temperature derating information.
9. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
For part marking data, visit http://www.coilcraft.com/colrcode.cfm.
Designer’s Kit C414 contains 10 of each 5% value
Core material Ferrite
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight 28 – 33 mg
Ambient temperature –40°C to +85°C with Irms current.
Maximum part temperature +125°C (ambient + temp rise). Derating.
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL) +100 to +350 ppm/°C
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging 2000 per 7″reel; 7500 per 13″ reel
Plastic tape: 8 mm wide, 0.3 mm thick, 4 mm pocket spacing,
2.0 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Document 578-1 Revised 10/12/15
1008AF Series (2520)
Typical L vs Frequency
12
11
10
9
8
7
6
5
4
3
2
1
0
0.1
10 µH
5.8 µH
3.9 µH
2.2 µH
1.1 µH
1 10
Frequency (MHz)
Typical L vs Current
12
11
10
9
8
7
6
5
4
3
2
1
0
0.01
10 µH
5.8 µH
3.9 µH
2.2 µH
1.1 µH
0.1 1
Current (A)
Document 578-2
Typical Q vs Frequency
40
35
30
1.1 µH
25 2.2 µH, 3.9 µH
20 10 µH 5.8 µH
15
10
5
0
100 0.1
1 10
Frequency (MHz)
100
0.110
2,79
max
0.115
2,92
max
Pick and place
material
0.02
0,51
0.075
1,91
max
(See
note)
Terminal wraparound:
10 approx 0.015/0,38 both ends
Recommended
Land Pattern
0.080 ±0.002 0.100
1,91 ±0,051 2,54
0.0205
0,5207
max
0.040
1,02
0.050
1,27
0.098 ±0.003
2,49 ±0,076
Dimensions are in
inches
mm
Note: Height dimension is before optional solder application. For maximum
height dimension including solder, add 0.006 in / 0,152 mm.
Document 578-2 Revised 10/12/15
|
PDF 파일 내의 페이지 : 총 2 페이지
제조업체: Coilcraft
( coilcraft )
1008AF-112XKLB inductor
데이터시트 다운로드 :
[ 1008AF-112XKLB.PDF ]
[ 1008AF-112XKLB 다른 제조사 검색 ]
국내 전력반도체 판매점
상호 : 아이지 인터내셔날
전화번호 : 051-319-2877
[ 홈페이지 ]
IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈
( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )
전력반도체 문의 : 010-3582-2743
관련 데이터시트
1008AF-112XKLB
Chip Inductors - Coilcraft
1008AF-112XKLC
Chip Inductors - Coilcraft
1008AF-112XKLD
Chip Inductors - Coilcraft