MSC1278-473KL 반도체 회로 부품 판매점
Coupled Inductors
|
|
 Coilcraft |
Document 922-1
Coupled Inductors–MSC1278
For SEPIC
Applications
The MSC1278 coupled inductors are designed with
high leakage inductance for use in SEPIC applications.
The loosely coupled windings (K ≈ 0.8) improve SEPIC
efficiency by reducing circulating current and provide
twice the ripple current reduction of separate inductors.
These inductors offer high efficiency and excellent cur-
rent handling in a rugged, low cost part. They are well
suited for use as a VRM inductors in high-current DC-DC
converters and VRM/VRD controllers.
They can also be used as two single inductors connected
in series or parallel.
01.428,34max
01.428,34max
123
X
Dot indicates pin1
Dash number
Internal code
0.317
8,05
max
0.197
5,0
0.197
5,0
34
21
0.138
3,5
0.059
1,5
Dimensions
are
in
inches
mm
Recommended
Land Pattern
0.157
4,0
0.217
5,5
2 1 0.177
3 4 4,5
0.079
2,0
12
L1 L2
34
1:1
+
L1
VIN Q1
C1
L2
D1
+
C2
+
Load VOUT
––
Typical SEPIC schematic
Refer to Application Note, Document 639,
“Selecting Coupled Inductors for SEPIC Applications.”
Visit http://www.coilcraft.com/apps/sepic/selector_2.cfm
for the Coilcraft on-line SEPIC Inductor Selector tool.
Core material Ferrite
Core and winding loss Go to online calculator
Terminations RoHS compliant matte tin over nickel over phos
bronze. Other terminations available at additional cost.
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Winding to winding isolation 500 Vrms
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 500/13″ reel; Plastic tape: 24 mm wide, 0.4 mm thick,
16 mm pocket spacing, 8.1 mm pocket depth
PCB washing Tested with pure water or alcohol only. For other
solvents, see Doc787_PCB_Washing.pdf.
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
Document 922-1 Revised 06/24/11
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.
Document 922-2
Coupled Inductors for SEPIC – MSC1278 Series
DCR SRF Coupling Leakage
Part Inductance2 max3 typ4 coefficient inductance5
number1
(µH)
(Ohms) (MHz)
typ
typ (µH)
MSC1278-103ML_
MSC1278-223KL_
MSC1278-333KL_
MSC1278-473KL_
10 ±20%
22 ±10%
33 ±10%
47 ±10%
0.058
0.096
0.15
0.18
20
12
9.5
7.8
0.80
0.82
0.85
0.83
2.75
5.85
10.1
14.5
Isat (A)6 Irms (A)
10% 20% 30% both one
drop drop drop windings7 winding8
8.80
6.00
5.50
3.70
10.0
6.80
6.10
4.34
10.66
7.26
6.52
4.60
2.56
1.99
1.59
1.45
3.62
2.81
2.25
2.05
1. When ordering, please specify termination and packaging code:
MSC1278-473KLD
Termination: L = RoHS compliant matte tin over nickel over phos
bronze
Special order:
T = RoHS tin-silver-copper (95.5/4/0.5) or
S = non-RoHS tin-lead (63/37).
Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic
tape (500 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter D instead.
2. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms,
0 Adc on an Agilent/HP 4284A LCR meter or equivalent. When leads
are connected in parallel, inductance is the same value. When leads
are connected in series, inductance is four times the value.
3. DCR is for each winding. When leads are connected in parallel, DCR
is half the value. When leads are connected in series, DCR is twice the
value.
4. SRF measured using an Agilent/HP 4191A or equivalent. When leads
are connected in parallel, SRF is the same value.
5. Leakage inductance is for L1 and is measured with L2 shorted.
6. DC current, at which the inductance drops the specified amount from
its value without current. It is the sum of the current flowing in both
windings.
7. Equal current when applied to each winding simultaneously that
causes a 40°C temperature rise from 25°C ambient. See temperature
rise calculation.
8. Maximum current when applied to one winding that causes a 40°C
temperature rise from 25°C ambient. See temperature rise calculation.
9. Electrical specifications at 25°C.
Refer to Doc 639 “Selecting Coupled Inductors for SEPIC Applications.”
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Coupled Inductor Core and Winding Loss Calculator
This web-based utility allows you to enter frequency, peak-to-peak
(ripple) current, and Irms current to predict temperature rise and overall
losses, including core loss. Go to online calculator.
Current Derating
110
100
90
80
70
60
50
40
30
20
10
0
-40
-20
0 20 40 60 80 100
Ambient temperature (°C)
120 140
L vs Current
100
10
47 µH
33 µH
22 µH
10 µH
L vs Frequency
100
47 µH
33 µH
22 µH
10 10 µH
1
0.1
1 10
Current (A)
1
100 0.1
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
1 10
Frequency (MHz)
100
Document 922-2 Revised 06/24/11
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.
|
PDF 파일 내의 페이지 : 총 2 페이지
제조업체: Coilcraft
( coilcraft )
MSC1278-473KL inductor
데이터시트 다운로드 :
[ MSC1278-473KL.PDF ]
[ MSC1278-473KL 다른 제조사 검색 ]
국내 전력반도체 판매점
상호 : 아이지 인터내셔날
전화번호 : 051-319-2877
[ 홈페이지 ]
IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈
( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )
전력반도체 문의 : 010-3582-2743
