EPL3012-152ML 반도체 회로 부품 판매점
Shielded Power Inductors
|
|
 Coilcraft |
Document 692-1
Shielded PowerInductors– EPL3012
• Low profile shielded power inductors; 3 × 3 × 1.3 mm max.
• Very low DCR, high SRF ratings, Isat ratings up to 2.0 A
Designer’s Kit C437 contains 5 each of all values
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Environmental RoHS compliant, halogen free
Terminations RoHS compliant tin-silver-copper (96.5/3/0.5) over tin over
nickel over silver-platinum. Other terminations available at additional cost.
Weight 38 – 42 mg
Ambient temperature –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature +125°C (ambient + temp rise). Derating.
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 2000/7″reel; 7500/13″ reel Plastic tape: 8 mm wide,
0.2 mm thick, 4 mm pocket spacing, 1.55 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Part number1
Inductance2
±20% (µH)
EPL3012-102ML_
EPL3012-152ML_
EPL3012-182ML_
EPL3012-222ML_
EPL3012-332ML_
1.0
1.5
1.8
2.2
3.3
EPL3012-472ML_ 4.7
EPL3012-103ML_ 10
EPL3012-223ML_ 22
DCR (Ohms)3
nom max
SRF typ4 Isat (A)5
Irms (A)6
(MHz)
10% drop 20% drop 30% drop 20°C rise 40°C rise
0.060 0.066
0.069 0.075
0.076 0.084
0.097 0.106
0.136 0.150
110
103
92
76
62
0.85 1.4 2.0
0.70 1.2 1.7
0.65 1.1 1.6
0.55 0.95 1.4
0.50 0.90 1.1
1.7 2.2
1.5 1.9
1.4 1.8
1.3 1.7
1.1 1.4
0.165 0.181
0.316 0.348
0.718 0.790
52
32
18
0.47 0.85 1.0
0.34 0.59 0.80
0.17 0.38 0.61
0.90 1.1
0.60 0.79
0.42 0.54
1. When ordering, please specify packaging code:
EPL3012-223MLC
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
D = 13″ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (7500 parts per
full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 4395A network analyzer or equivalent.
5. DC current at 25°C that causes the specified inductance drop from its
value without current. Click for temperature derating information.
6. Current that causes the specified temperature rise from 25°C ambient.
This information is for reference only and does not represent absolute
maximum ratings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 692-1 Revised 09/08/15
Document 692-2
Shielded Power Inductors – EPL3012 Series
L vs Current
L vs Frequency
100 100
22 µH
10
22 µH
10 10 µH
10 µH
4.7 µH
4.7 µH
3.3 µH
3.3 µH
2.2 µH
1.8 µH
2.2 µH
1.5 µH
1
1.8 µH
1 1.0 µH
1.5 µH
1.0 µH
0.1
0.01
0.1 1
Current (A)
0.1
10 0.1
1 10
Frequency (MHz)
100
2nd
significant
digit
0.118 ±0.008
3,0 ±0,2
0.118 ±0.008
3,0 ±0,2
1st
Multiplier
significant
digit
Part Marking
0.051
1,30
max
Start
Finish
0.082
2,08
Part Marking
Part number
EPL3012-102
EPL3012-152
EPL3012-182
EPL3012-222
EPL3012-332
EPL3012-472
EPL3012-103
EPL3012-223
Value
1.0 µH
1.5 µH
1.8 µH
2.2 µH
3.3 µH
4.7 µH
10 µH
22 µH
1st digit
Brown
Brown
Brown
Red
Orange
Yellow
Brown
Red
2nd digit
Black
Green
Gray
Red
Orange
Violet
Black
Red
Multiplier
Red
Red
Red
Red
Red
Red
Orange
Orange
Note: All marked parts have three dots.Black dot, used only on the -102 and ‑103
as second significant digit, may be very difficult to see.
0.106 ±0.008
2,69 ±0,20
0.126
3,2
0.043
1,10
min
0.050
1,26
typ
0.030 ±0.008
0,77 ±0,20
Small surface blemishes are not unusual and do
not adversely affect performance.
Wire may be visible inside the voids.
Acceptable void sizes:
Top: 0.01 in / 0,254 mm × 0.01 in / 0,254 mm
Sides: 0.02 in / 0,5 mm × 0.047 in / 1,2 mm
0.044
1,12
Recommended
Land Pattern
Dimensions are in
inches
mm
Document 692-2 Revised 09/08/15
|
PDF 파일 내의 페이지 : 총 2 페이지
제조업체: Coilcraft
( coilcraft )
EPL3012-152ML inductor
데이터시트 다운로드 :
[ EPL3012-152ML.PDF ]
[ EPL3012-152ML 다른 제조사 검색 ]
국내 전력반도체 판매점
상호 : 아이지 인터내셔날
전화번호 : 051-319-2877
[ 홈페이지 ]
IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈
( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )
전력반도체 문의 : 010-3582-2743
