|
United Chemi |
.DKataSMheet4GU.comSeriesⅢ Miniature
ww Ⅲ General Purpose
w mⅢ Solvent Proof
oⅢ105؇C
.cMaximum
Temperature
heet4UThe KMG series capacitors are designed for general purpose use with an operating temperature
Srange for most of these capacitors from 55؇C to 105؇C. The KMG series is a miniaturized version
of the KME series with a load life of 1,000 hours at 105؇C with the rated ripple current applied.
taThe KMG series capacitors below 350 volts were developed to withstand HCFC cleaning agents for
five minutes by ultrasonic, vapor or immersion. This solvent proof design allows all circuit board
acomponents to be cleaned together, at the same time, without resorting to more expensive epoxy
end-sealed capacitors. Refer to the Mini-Glossary for recommended cleaning conditions.
.DSummary of Specifications
wwⅢ Radial lead terminals.
mⅢ Capacitance range: 0.1 to 22,000µF.
w .coⅢ Voltage range: 6.3 to 450VDC.
UⅢ Operating temperature range: 55؇C to 105؇C for 6.3 to 100V; 40؇C to 105؇C
t4for 160 to 400V; 25؇C to 105؇C for 450V.
eⅢ Leakage current: See specifications table for leakage current values at 20؇C.
heⅢ Standard capacitance tolerance: ؓ20%
SⅢ Nominal case size (DL): 511mm to 1840mm.
taⅢ Rated lifetime: 1,000 to 2,000 hours at 105؇C with the rated ripple current applied,
www.Dadepending on rated voltage and case size.
136 United Chemi-Con, Inc. 9801 W. Higgins Road, Rosemont, IL 60018 Tel 847-696-2000 Fax 847-696-9278 www.chemi-con.com
KMG Series
KMG Specifications
Item
Rated Voltage Range
Operating Temperature Range
Capacitance Range
Capacitance Tolerance
Leakage Current
Dissipation Factor ( Tan ␦)
Low Temperature
Characteristics
Ripple Current Multipliers
Refer to Section 4 of the
Mini-Glossary for explanation
of Ripple Current Multipliers.
Load Life
Shelf Life
Others
6.3 to 100VDC
55 to 105؇C
0.1 to 22,000F
ؓ20% ( M ) at 20؇C, 120Hz
At 20؇C
Characteristics
160 to 400VDC
40 to 105؇C
450VDC
25 to 105؇C
DC Rated Voltage
Test Time
Leakage Current (A )
6.3 -100V
After 1 minute I 0.03CV or 4A, whichever is greater.
160 - 450V
After 1 minute
After 5 minutes
CV ≤ 1,000: I 0.1CV40
CV ≤ 1,000: I 0.03CV15
CV >1,000: I 0.04CV100
CV >1,000: I 0.02CV25
Where I = Leakage current (A ), C = Nominal capacitance (F ) and V = Rated voltage ( V )
At 20؇C, 120Hz
Rated Voltage ( V )
6.3 10 16 25 35 50 63 100 160 - 250 350 - 450
Tan ␦ ( DF )
0.34 0.24 0.20 0.16 0.14 0.12 0.10 0.08 0.20
0.24
When nominal capacitance exceeds 1,000F, add 0.02 to the values above for each 1,000F increase.
At 120Hz, impedance ( Z ) ratio between the 25؇C or 40؇C value and 20؇C value shall not
exceed the values given below.
Rated Voltage ( V )
6.3 10 16 25 35 50 -100 160 - 250 350 - 400 450
Z (25؇C ) / Z (20؇C ) 5 4 3 2 2
2
3
66
Z (40؇C ) / Z (20؇C ) 12
10
8
5
4
3
4
6–
Ambient Temperature (؇C )
85؇C
1.75
105؇C
1.00
Frequency (Hz )
Capacitance (F )
≤ 3.3F
4.7- 33F
47-1000F
≥ 2200F
50Hz
0.65
0.75
0.80
0.85
120Hz
1.00
1.00
1.00
1.00
300Hz
1.35
1.25
1.15
1.03
1kHz
1.75
1.50
1.30
1.05
10kHz
2.30
1.75
1.40
1.08
100kHz
2.50
1.80
1.50
1.08
The following specifications shall be satisfied when the capacitors are restored to 20؇C after
subjecting them to the DC rated voltage for the specified test time at 105؇C with the rated
ripple current applied. The sum of DC voltage and peak AC voltage must not exceed the full
rated voltage of the capacitors.
Case Diameter Test Time
Ø5 - Ø10mm
Ø12.5 - Ø18mm
1,000 hours for 6.3 - 450V
1,000 hours for 6.3 -100V
2,000 hours for 160 - 450V
Capacitance change: ≤ ؓ20% of initial measured value
Tan ␦ ( DF )
: ≤ 200% of initial specified value
Leakage current : ≤ initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20؇C after
exposing them for 1,000 hours at 105؇C without voltage applied. The rated voltage shall be
applied to the capacitors for a minimum of 30 minutes, at least 24 hours and not more than
48 hours before the measurements.
Capacitance change: ≤ ؓ20% of initial measured value
Tan ␦ ( DF )
: ≤ 200% of initial specified value
Leakage current : ≤ initial specified value for 6.3 -100V
: ≤ 500% of initial specified value for 160 - 450V
Satisfies characteristic W of JIS C5141
United Chemi-Con, Inc. 9801 W. Higgins Road, Rosemont, IL 60018 Tel 847-696-2000 Fax 847-696-9278 www.chemi-con.com 137
|