LPQ353-CEF 반도체 회로 부품 판매점
AC-DC / 261W - 500W
|
|
 Emerson |
350 Watts
LPQ350 Series
Total Power: 350 Watts
Input Voltage: 85-264 VAC
120-300 VDC
# of Outputs: Quad
Electrical Specs
Input
Input range
Frequency
Inrush current
Efficiency
EMI filter
Power factor
Safety ground leakage
current
85-264 VAC; 120-300 VDC
47-440 Hz
38 A max., cold start @ 25°C
75% typical at full load
FCC Class B conducted and radiated
CISPR 22 Class B conducted and
radiated EN55022 Class B conducted
and radiated VDE 0878 PT3 Class B
conducted and radiated.
0.99 typical
<0.5 mA @ 50/60 Hz, 264 VAC input
Special Features
• Active power factor correction
• IEC EN61000-3-2 compliance
• Remote sense on 1st and 4th output
• Power fail and remote inhibit
• Single wire current sharing
• Built-in EMI filter
• Adjustable floating 4th output
• 2 Supervisory output 5 V and 12 V
• Overvoltage protection
• Overload protection
• Thermal overload protection
• DC power good
• 135 khz switching frequency
• Cover -C
• Optional with fan cover -CF
• Optional end-mounted fan -CEF
Environmental
Operating temperature: 0° to 50°C ambient
derate each output at 2.5% per degree from 50° to
70°C
Electromagnetic susceptibility: Designed to meet
IEC 801, -2, -3, -4, -5, -6, Level 3
Humidity: Operating; non-condensing
5% to 95%
Vibration: Three orthogonal axes, sweep at
1 oct/min, 5 min. dwell at four major resonances
0.7 G peak 5 Hz to 500 Hz, operational
Storage temperature: -40° to 85°C
Temperature coefficient: ±.04% per °C
MTBF demonstrated: >550,000 hours at full load
and 25°C ambient conditions
Output
Maximum power
Adjustment range
Supervisory output
Hold-up time
Overload protection
Overvoltage protection
With cover: 350 W with 30 CFM forced
air, (-C) (-CF) (-CEF)
± 5% min. on main: 3.3-24 V on output
4
5 V @ 500 mA regulated, 12 @ 150 mA
x2
20 ms @ 350 W load, 115 VAC nominal
line
Short circuit protection on all outputs.
Case overload protected @ 110-145%
above peak rating
5 V output: 5.7-6.7 VDC.
Logic Control
Power failure
TTL logic signal goes high 50-150 msec
after 5 V output. It goes low at least 4
msec before loss of regulation
Remote on/off
Requires an external contact (N.O or
N.C) to inhibit outputs
DC-OK
TTL logic goes high 50-150 msec after
5 V output. It goes low when there is
loss of regulation.
Remote sense
Compensates for 0.5 V lead drop min.
Will operate without remote sense
Safety
connected. Reverse connection
protected.
VDE 0805/EN60950 (IEC950)
UL UL1950
CSA CSA 22.2-234 Level 5
NEMKO EN 60950/EMKO-TUE
CB Certificate and report
CE Mark (LVD)
21310-3336-0001
E186249
LR109492C
P97102061 (74-sec) 203
4048, 4049
rev 12.10.03
Technical Support: (888) 41-ASTEC or (407) 241-2752
128
Americas: (760) 930-4600
Europe (UK) 44 (1384) 842-211
Asia (HK) 852-2437-9662
AMERICAS
5810 Van Allen Way
Carlsbad, CA 92008
Telephone: 760-930-4600
Facsimile: 760-930-0698
EUROPE
Astec House, Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX, UK
Telephone: 44 (1384) 842-211
Facsimile: 44 (1384) 843-355
ASIA
Units 2111-2116, Level 21
Tower1, Metroplaza
223, Hing Fong Road
Fwai Fong, New Territories
Hong Kong
Telephone: 852-2437-9662
Facsimile: 852-2402-4426
Ordering Information
Model
Number
Output
Voltage
Minimum
Load
Maximum Load with
30 CFM Forced Air
Peak
Load1
Regulation2 Ripple
P/P (PARD)3
LPQ352-C
+5 V
+12 V
-12 V
3.3-24 V
5A
0A
0A
*1 A
50 A
12 A
6A
6A
60 A
14 A
8A
8A
±2% 50 mV
±3% 120 mV
±3% 120 mV
±3% 240 mV, max.
LPQ353-C
+5 V
+15 V
-15 V
3.3-24 V
5A
0A
0A
*1 A
50 A
12 A
6A
6A
60 A
14 A
8A
8A
±2% 50 mV
±3% 150 mV
±3% 150 mV
±3% 240 mV, max.
1. Peak current lasting <30 seconds with a maximum 10% duty cycle.
2. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.
3. Peak-to-peak with 20 MHz bandwidth and 10 µF in parallel with a 0.1 µF capacitor at rated line voltage and load ranges.
4. 4th output 3.3-24 V factory set at 5 V.
5. * Minimum load required when the output is set below 5 volts.
6. If optional CF or CEF fans are not used, 30CFM forced air cooling needs to be provided and is required through the
length of the power supply. Not convection rated.
7. Remote inhibit resets OVP latch
Note: -CF suffix added to the model number indicates cover with fan,
-CEF suffix added to model number indicates end-mounted fan chassis.
Pin Assignments
SK1 PIN 1 Neutral
PIN 2
Line
PIN 3
Ground
SK2 PIN 1 +12 / 15 V
PIN 2
Common
PIN 3
Common
PIN 4
-12 / 15 V
PIN 5
3.3-25 V RET Float
PIN 6
3.3-25 V Float
SK3 PIN 1 + Sense V 4
PIN 2
- Sense V 4
PIN 3
+Sense V 1
PIN 4
-Sense V 1
PIN 5
POK
PIN 6
C.Share
PIN 7
DC-OK
PIN 8
Inhibit (N.O.)
PIN 9
Inhibit (N.C.)
PIN 10
COM
SK4 PIN 1 + Fan 1 (12V@150mA)
PIN 2
– Common
SK5 PIN 1 + 5V aux (5V@100mA)
PIN 2
– Common
SK6 PIN 1 + Fan 2 (12V@150mA)
PIN 2
– Common
Mating Connectors
SK3 Molex: 22-01-1084
PINS: 08-70-0057
SK4 Molex 22-01-3027
PINS: 08-50-0114
SK5 Molex 22-01-3027
PINS: 08-50-0114
SK6 Molex 22-01-3027
PINS: 08-50-0114
Astec Connector Kit #70-841-011, includes all of the above.
www.astecpower.com
6-32 (2 places)
M3
Main Output
Terminal
(6 places)
SK2 SK3
Block TB1
6 5 4 3 2 1 1234 5 678910
+ve -ve
J1 SK5 5V aux
SK4 fan
M3 (4 places)
#6-32 UNC (8 places)
.24 (6.1)
SK6
Top pot.
=V4 adjust
Bottom pot.
=V1 adjust
3.68
(93.6)
Optional
(-CF) 3.15
Cover (80)
with Fan
2.17
(55)
5.46
(138.6)
6.64
(168.6)
8.52
(216.4)
9.0
(228.6)
10.78
(273.8)
6-32 (3 places)
321
SK1
5.0 (127.0)
.55
(14)
1.30
(33.0)
.79
(20)
3.42 (87.0)
Optional
(-CEF)
Cover
with fan
1.18 (30.0)
2.5
(63.5)
3.5
(88.9)
Notes:
1. Specifications subject to change without notice.
2. All dimensions in inches (mm), tolerance ±.02”.
3. Specifications are at factory settings
4. To enable normally closed Remote Inhibit,
cut Jumper J1.
5. Mounting maximum insertion depth is 0.12”.
6. Warranty: 1 year
7. Weight: 4 lb. / 1.8kg.
129
|
PDF 파일 내의 페이지 : 총 2 페이지
제조업체: Emerson
( emerson )
LPQ353-CEF data
데이터시트 다운로드 :
[ LPQ353-CEF.PDF ]
[ LPQ353-CEF 다른 제조사 검색 ]
국내 전력반도체 판매점
상호 : 아이지 인터내셔날
전화번호 : 051-319-2877
[ 홈페이지 ]
IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈
( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )
전력반도체 문의 : 010-3582-2743
