APC78106 반도체 회로 부품 판매점
ADSL CPE Hybrid
|
|
 Bel Fuse |
ADSL CPE Hybrid
APC78106
OPERATING TEMPERATURE -40°C TO +85°C
FEATURES
• APC78106 is designed to interface with Alcatel’s MTK20150 and MTK20141 ADSL
transceiver chip sets to optimize customer premises equipment (CPE) designs. The
Hybrid contains every component required between the analog front end chip and the connector including
www.DataSheet4U.ctohme line interface transformer and common mode chokes, line protection circuitry, transmit and receive filters
(excluding line driver and parallel capacitors).
• The hybrid was designed jointly by APC and Alcatel to optimize the transmission capabilities of the
“Dynamite” chip set. It meets or exceeds the requirements of the standards as specified in TS101 388,
T1.413 and ETR328. It also provides BS EN60950 / IEC60950 / TS 001 / AS/NZS 3260 / CAN/
CSA C22.2 Np. 950-95 / UL1950 and CB Certificate supplementary insulation and UL Component
Recognition (File No. E175058).
SCHEMATIC
Pin
(1-2)
Pin
(3-16)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
TNV
SELV
Tip
Ring
Txp
Txn
A_Gnd_Tx
N/C
Hybrid Gnd
Plane
Rxp
Pin 9
Rxn
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
Pin 16
Pin 17
Pin 18
8016 pin 4 / EL1510CS pin 3
8016 pin 2 / EL1510CS pin 1
8016 pin 3 / EL1510CS pin 2
N/C
8016 pin 21 / EL1510CS pin 5
8016 pin 23 / EL1510CS pin 7
8016 pin 22 / EL1510CS pin 6
N/C
N/C
NOTES:
ADI 8016 LINE DRIVER = 24 LEAD BATWING
ELANTEC EL1510CS LINE DRIVER = 8 PIN SO
1. ALL TRACES BETWEEN APC PINS 10 AND 14 AND ADI LINE DRIVER PINS 4 AND 21 RESPECTIVELY, MUST BE KEPT SYMMETRICAL, PARALLEL AND EQUIDISTANT.
2. TWO 4.7NF PARALLEL CAPACITORS SHOULD BE PLACED BETWEEN ADI LINE DRIVER PIN 4 AND AGT (A_GND_TX) AND BETWEEN ADI LINE DRIVER PIN 21 AND AGT
(A_GND_TX). THESE NEED TO BE PLACED AS CLOSE TO THE ADI LINE DRIVER AS POSSIBLE.
SAFETY NOTE:
THE CIRCUIT ON THE LC SIDE OF THE TRANSFORMER IS A SELV CIRCUIT AND THE CIRCUIT ON THE LINE SIDE OF THE TRANSFORMER IS A TNV CIRCUIT.
- CIRCUITRY DESIGNATED AS SELV SHALL ONLY BE CONNECTED TO OTHER SELV CIRCUITS (UNDER NORMAL AND SINGLE FAULT CONDITIONS) IN END
INSTALLATION
- DO NOT PLACE HYBRID AGAINST OTHER COMPONENT PARTS ATTAINING EXCESSIVE TEMPERATURES.
MECHANICAL
51.26
48.26
33 33.02
19
NOTES:
12
5.4
29.7
NOT TO SCALE
TOLERANCE +/- 0.2MM
ALL DIMENSIONS IN MM
PIN DIA. 0.75MM MAX.
18
2.54
10
©2003 Bel Fuse Inc. Specifications subject to change without notice. 05.20.03
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
Page 1
|
PDF 파일 내의 페이지 : 총 1 페이지
제조업체: Bel Fuse
( belfuse )
APC78106 data
데이터시트 다운로드 :
[ APC78106.PDF ]
[ APC78106 다른 제조사 검색 ]
국내 전력반도체 판매점
상호 : 아이지 인터내셔날
전화번호 : 051-319-2877
[ 홈페이지 ]
IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈
( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )
전력반도체 문의 : 010-3582-2743
