|
GTM |
www.DataSheet4U.com
ISSUED DATE :2006/08/18
REVISED DATE :
GN809
Processor Supervisory
Description
The GN809 family allows the user to customize the CPU reset function without any external components. The
user has a large choice of reset voltage thresholds and output driver configurations, all of which are preset at
the factory. Each wafer is trimmed to the customer’s specifications.
These circuits monitor the power supply voltage of up based systems. When the power supply voltage drops
below the voltage threshold a reset is asserted immediately (within an interval TD1). The reset remains asserted
after the supply voltage rises above the voltage threshold for a time interval, TD2. The reset output is active low
(RESETB). The reset output may be configured as either push/pull or open drain. The state of the reset output
is guaranteed to be correct for supply voltage greater than 1V.
Space saving SOT-23 package and micropower quiescent current (<3.0uA) make this family a natural for
portable battery powered equipment.
Features
Tight Voltage Threshold Tolerance ±1.5%
Wide Temperature Range -40 to 80
Low Quiescent Current <3.0uA
Lead Free Products Meet RoHS standards
Applications
Power Supplies
Data Acquisition Systems
Applications using CPUs
Consumer Electronics
Computer Peripherals
Portable Electronics
Package Dimensions
Typical Operating Circuit
GN809
Note:* External pull-up resistor is required if
open-drain output is used. 10k is recommended.
SOT-23
Block Diagram
GN809 with Push-Pull RESET
REF.
A
B
C
D
E
F
Millimeter
Min. Max.
2.70 3.10
2.40 2.80
1.40 1.60
0.35 0.50
0 0.10
0.45 0.55
REF.
G
H
K
J
L
M
Millimeter
Min. Max.
1.90 REF.
1.00 1.30
0.10 0.20
0.40 -
0.85 1.15
0 10
GN809
Page: 1/4
www.DataSheet4U.com
ISSUED DATE :2006/08/18
REVISED DATE :
Pin Description
Pin Name
Pin Description
Gnd Ground
RESETB
RESETB is active low and push-pull output
VIN
Positive power supply. A reset is asserted after this voltage drops below a predetermined. After VIN rises
above that level the reset output remains asserted until the end of the reset timeout period.
Absolute Maximum Ratings
Parameter
Input Voltage
Input Current, VIN
Output Current, RESETB
Symbol
VIN
Ratings
7
20
20
Unit
V
mA
mA
Rate of Rise, VIN
Ambient Temperature Range
Junction Temperature Range
Storage Temperature Range
Maximum Junction Temperature
Thermal Resistance
TA
TJ
TSTG
Tj Max
jc
ja
100
-40 ~ +85
-40 ~ +125
-65 ~ +150
150
140
285
V/ s
/W
/W
Internal Power Dissipation
PD 400
mW
Solder Iron (10 Sec)*
350
EDS Classification
B**
Caution: Stress above the listed absolute maximum rating may cause permanent damage of the device
*MIL-STDS-202G 210F
**HBM B: 2000V ~ 3999V
Electrical Characteristics Ta=25 (unless otherwise noted)
Parameter
VIN Range
Supply Current
Symbol
VRange
IIN
Condition
TA=-40 ~ +85
VIN= VTH*1.10
VIN= VTH*1.10, TA=-40 ~ +85
Reset Threshold Voltage
VTH
TA=-40 ~ +85
Min
1
-
-
VTH(NOM)
-1.5%
VTH(NOM)
-2.0%
TYP
-
-
-
-
-
Max
5.5
3.0
5.0
VTH(NOM)
+1.5%
VTH(NOM)
+2.0%
Unit
V
A
mV
Hysteresis Range (Note2)
RESET Threshold
Tempco (Note2)
RESETB Output
Voltage Low
VHYST
VRelease-VTH (Note1)
VOL
VIN<VTH(MIN), ISINK=1.2mA
TA=-40 ~ +85
10 30 60
mV
30 50 160 ppm
-
- 0.2
V
RESETB Output
Voltage High
VOH
VIN>VTH(MAX)
ISOURCE=0.5mA
VIN>1.8V
ISOURCE=0.15mA
1.8V VIN>1.0V
0.8*VIN
-
-
V
VIN to Reset Delay
Reset Timeout Period
TD1 VIN= VTH-100mV, TA=-40 ~ +85
TD2 TA=-40 ~ +85
- 40 -
80 150 230
S
mS
Note 1: The data based on VTH=2.7V part type.
2: Guaranteed by Design
GN809
Page: 2/4
|