SPP-ID976 반도체 회로 부품 판매점
(SPP-ID975 / SPP-ID976) Service Manual
|
|
 Sony |
SPP-ID975/ID976wwwSVer.ED1.0Ra1t9Va99SI. 1Ch1eEet4MUA.cNomUAL
US Model
SPP-ID975
Canadian Model
SPP-ID976
t4U.comGeneral
Frequency band (SPP-ID975)
902 – 928 MHz
eFrequency band (SPP-ID976)
923.1 – 927.75 MHz
Base phone : 18 µW
eHandset : 73 µW
Operating channel
h30 channels
Dial signal
Tone, 10 PPS (pulse) selectable
SSupplied accessories
AC power adaptor AC-T122 (1)
taTelephone line cords (2)
Wall bracket for base phone (1)
Rechargeable battery pack BP-T23 (1)
aHandset
Power source
Rechargeable battery pack BP-T23
.DBattery charging time
Approx. 12 hours
Battery life
Standby : Approx. 7 days
wTalk : Approx. 6 hours
Dimensions
Approx. 58 × 177 × 46 mm (w/h/d),
wantenna excluded
(approx. 2 3/8 × 7 × 1 13/16 inches)
wAntenna: Approx. 72 mm
Photo: SPP-ID975
SPECIFICATIONS
Base phone
Power source
DC 9V from AC power adaptor
AC-T122
Battery charging time
Approx. 24 hours
Dimensions
Approx. 166 × 63 × 225 mm (w/h/d),
antenna excluded
(approx. 6 5/8 × 2 1/2 × 8 7/8 inches)
Antenna: Approx. 120 mm
(approx. 4 3/4 inches)
Mass
Approx. 595 g
(approx. 1 lb 9 oz), wall bracket excluded
Design and specifications are subject to
change without notice.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
(approx. 2 7/8 inches)
Mass
Approx. 270 g
(approx. 9.5 oz), battery included
MICROFILM
wwCwOR.DDaLtEaSSSheTeELt4EUP.HcOoNmE
–1–
SPP-ID975/ID976
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
For schematic diagrams
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
• C : panel designation.
• U : B+ Line.
• Power voltage is dc 9 V and fed with regulated dc power
supply from external power voltage jack. (BASE PHONE)
• Power voltage is dc 12 V and fed with regulated dc power
supply from J1008 with 100 Ω in series. (BASE PHONE)
• Power voltage is dc 3 V and fed with regulated dc power
supply from battery terminal. (HANDSET)
• Voltage is dc with respect to ground under no-signal
condition.
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Signal path.
N : TX (To Tel Line)
O : RX (From Tel Line)
P : bell
For printed wiring boards
• X : parts extracted from the component side.
• : Carbon pattern.
• z : Through hole.
• b : Pattern from the side which enables seeing.
(The other layer’s patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B)
pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A)
parts face are indicated.
4-3. SCHEMATIC DIAGRAM — BASE MAIN SECTION (1/2) —
– 25 –
– 26 –
|
PDF 파일 내의 페이지 : 총 6 페이지
제조업체: Sony
( sony )
SPP-ID976 data
데이터시트 다운로드 :
[ SPP-ID976.PDF ]
[ SPP-ID976 다른 제조사 검색 ]
국내 전력반도체 판매점
상호 : 아이지 인터내셔날
전화번호 : 051-319-2877
[ 홈페이지 ]
IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈
( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )
전력반도체 문의 : 010-3582-2743
관련 데이터시트
SPP-ID975
(SPP-ID975 / SPP-ID976) Service Manual - Sony
SPP-ID975
Cordless Telephone - Sony
SPP-ID976
(SPP-ID975 / SPP-ID976) Service Manual - Sony