|
Sipex |
® SP2525
+3.0V to +5.5V USB Power Control Switch
s Compliant to USB Specifications
s +3.0V to +5.5V Input Voltage Range
s Open Drain Error Flag Output
s 2.7V Undervoltage Lockout
s 500mA Minimum Continuous Load
Current
s 1.25A Short Circuit Current Limit
s 140mΩ Maximum On-Resistance
s 80µA On-State Supply Current
s 1µA Shutdown Current
s Thermal Shutdown
s 1ms Soft-Start Power Up
s Active-High Version: SP2525-1
s Active-Low Version: SP2525-2
DESCRIPTION
The SP2525 device is a single +3.0V to +5.5V USB Supervisory Power Control Switch ideal
for self-powered and bus-powered Universal Serial Bus (USB) applications. The SP2525
device has low on-resistance (80mΩ typical) and can supply 500mA minimum. The fault
currents are limited to 2.0A typical and the flag output pin is available to indicate fault
conditions to the USB controller. The 1ms soft start of the SP2525 device will eliminate any
momentary voltage drop on the upstream port that may occur when the switch is enabled in
bus-powered applications. The thermal shutdown feature will prevent permanent damage to
the SP2525 device when subjected to excessive current loads. The under voltage lockout feature
will ensure that the SP2525 device will remain off unless there is a valid input voltage present.
Rev. 8/21/01
EN 1
FLG 2
GND 3
NC 4
SP2525
8 OUT
7 IN
6 OUT
5 NC
SP2525 +3.0 to +5.5 Power Control Switch
1
© Copyright 2001 Sipex Corporation
ABSOLUTE MAXIMUM RATINGS
These are stress ratings only and functional operation
of the device at these ratings or any other above those
indicated in the operation sections of the specifications
below is not implied. Exposure to absolute maximum
rating conditions for extended periods of time may
affect reliability.
Supply Voltage.......................................-0.3V, +6.0V
Operating Temperature......................-40˚C to +85˚C
Storage Temperature.......................-65˚C to +150˚C
Power Dissipation Per Package
8-pin NSOIC (derate 6.14mW/OC above +70OC).......500mW
SPECIFICATIONS
Unless otherwise noted, the following specifications apply for VIN = +5.0V and TAMB = 25OC.
PARAMETER
MIN. TYP. MAX. UNITS
CONDITIONS
Operating Voltage Range, VIN
Supply Current, IIN
3.0 5.5
0.05 5.0
80 140
V
µA
enable off, no output load
enable on, no output load
Enable Input Threshold Voltage
2.1 2.4
0.8 1.9
V
low to high transition
high to low transition
Enable Input Current
Enable Input Capacitance
0.01 1
0.01 1
1
µA
VEN=VOH(min)=2.4V
VEN=VOL(max)=0.8V
pF
Switch Resistance
Output Turn-On Delay
Output Turn-On Rise Time
Output Turn-Off Delay
Output Turn-Off Fall Time
Output Leakage Current
80 140 mΩ 3.0V<VIN<5.5V,IL<500mA
0.5 ms RL=10Ω
1 ms RL=10Ω
1 20 µs RL=10Ω
1 20 µs RL=10Ω
.02 10
µA
Current Limit Threshold
2.0 2.8
A Ramped load applied
Short Circuit Current Limit
Over-Temperature Shutdown
Threshold
0.5 0.75 1.25
135
125
A VOUT = 0V
OC
increasing temperature
decreasing temperature
Error Flag Output Resistance
Error Flag Off Current
UVLO Threshold
10 25
15 40
0.01 1
2.7 3.0
2.5 2.6
Ω
VIN=5V,IL=10mA
V =3.3V,I =10mA
IN L
µA VFLAG=5V
V
VIN increasing, TMIN to TMAX
VIN decreasing TMIN to TMAX
Rev. 8/21/01
SP2525 +3.0 to +5.5 Power Control Switch
2
© Copyright 2001 Sipex Corporation
|