|
Motorola Semiconductors |
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Product Preview
64K x 4 Bit Static RAM
The MCM6709BR is a 262,144 bit static random access memory organized as
65,536 words of 4 bits. Static design eliminates the need for external clocks or
timing strobes.
Output enable (G) is a special control feature that provides increased system
flexibility and eliminates bus contention problems.
The MCM6709BR meets JEDEC standards and is available in a revolutionary
pinout 300 mil, 28 lead plastic surface–mount SOJ package.
• Single 5 V ± 10% Power Supply
• Fully Static — No Clock or Timing Strobes Necessary
• All Inputs and Outputs are TTL Compatible
• Center Power and I/O Pins for Reduced Noise
• Three State Outputs
• Fast Access Times:
MCM6709BR–6 = 6 ns
MCM6709BR–7 = 7 ns
MCM6709BR–8 = 8 ns
BLOCK DIAGRAM
A
A
A
A
A
A
ROW
••
DECODER •
MEMORY MATRIX
512 ROWS x 128 x 4
COLUMNS
A
A
A
DQ
COLUMN I/O
••
••
•
••
•
INPUT
DATA
COLUMN DECODER
•
CONTROL
DQ
AA A AAA A
E
W
G
Order this document
by MCM6709BR/D
MCM6709BR
J PACKAGE
300 MIL SOJ
CASE 810B–03
PIN ASSIGNMENT
A1
A2
A3
A4
E5
DQ 6
VCC 7
VSS 8
DQ 9
W 10
A 11
A 12
A 13
A 14
28 A
27 A
26 A
25 A
24 G
23 DQ
22 VSS
21 VCC
20 DQ
19 A
18 A
17 A
16 A
15 NC
PIN NAMES
A . . . . . . . . . . . . . . . . . . . Address Inputs
W . . . . . . . . . . . . . . . . . . . . Write Enable
G . . . . . . . . . . . . . . . . . . . Output Enable
E . . . . . . . . . . . . . . . . . . . . . . Chip Enable
DQ . . . . . . . . . . . . . . . Data Input/Output
VCC . . . . . . . . . . . . + 5 V Power Supply
VSS . . . . . . . . . . . . . . . . . . . . . . . Ground
NC . . . . . . . . . . . . . . . . . No Connection
All power supply and ground pins must
be connected for proper operation of the
device.
This document contains information on a new product under development. Motorola reserves the right to change or discontinue this product without notice.
REV 2
3/17/97
M© OMoTtoOroRla,OInLc.A19F97AST SRAM
MCM6709BR
1
TRUTH TABLE (X = Don’t Care)
E GW
Mode
H X X Not Selected
L HH
Read
L LH
Read
LXL
Write
Output
High–Z
High–Z
Dout
Din
Cycle
—
—
Read Cycle
Write Cycle
ABSOLUTE MAXIMUM RATINGS (See Note)
Rating
Symbol
Value
Unit
Power Supply Voltage
VCC
– 0.5 to + 7.0
V
Voltage Relative to VSS for Any Pin
Except VCC
Vin, Vout – 0.5 to VCC + 0.5 V
Output Current (per I/O)
Iout ± 30 mA
Power Dissipation
PD 2.0 W
Temperature Under Bias
Tbias
– 10 to + 85
°C
Operating Temperature
TA
0 to + 70
°C
Storage Temperature — Plastic
Tstg
– 55 to + 125
°C
NOTE: Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are
exceeded. Functional operation should be restricted to RECOMMENDED OPER-
ATING CONDITIONS. Exposure to higher than recommended voltages for
extended periods of time could affect device reliability.
This device contains circuitry to protect the
inputs against damage due to high static volt-
ages or electric fields; however, it is advised
that normal precautions be taken to avoid appli-
cation of any voltage higher than maximum
rated voltages to this high–impedance circuit.
This BiCMOS memory circuit has been de-
signed to meet the dc and ac specifications
shown in the tables, after thermal equilibrium
has been established. The circuit is in a test
socket or mounted on a printed circuit board
and transverse air flow of at least 500 linear feet
per minute is maintained.
DC OPERATING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V ± 10%, TA = 0 to 70°C, Unless Otherwise Noted)
RECOMMENDED OPERATING CONDITIONS
Parameter
Symbol
Min
Supply Voltage (Operating Voltage Range)
Input High Voltage
VCC
VIH
4.5
2.2
Input Low Voltage
VIL – 0.5**
* VIH (max) = VCC + 0.3 V dc; VIH (max) = VCC + 2.0 V ac (pulse width ≤ 2.0 ns) or I ≤ 30.0 mA.
** VIL (min) = – 0.5 V dc @ 30.0 mA; VIL (min) = – 2.0 V ac (pulse width ≤ 2.0 ns) or I ≤ 30.0 mA.
Typ Max Unit
5.0 5.5 V
— VCC + 0.3* V
— 0.8 V
DC CHARACTERISTICS
Parameter
Input Leakage Current (All Inputs, Vin = 0 to VCC)
Output Leakage Current (E = VIH, Vout = 0 to VCC)
Output High Voltage (IOH = – 4.0 mA)
Output Low Voltage (IOL = 8.0 mA)
Symbol
Ilkg(I)
Ilkg(O)
VOH
VOL
Min
—
—
2.4
—
Max
± 1.0
± 1.0
—
0.4
Unit
µA
µA
V
V
POWER SUPPLY CURRENTS
Parameter
Symbol MCM6709BR–6 MCM6709BR–7 MCM6709BR–8 Unit
AC Active Supply Current (Iout = 0 mA, VCC = max,
ICCA
215
205
195 mA
f = fmax)
AC Standby Current (E = VIH, VCC = max, f = fmax)
ISB1
95
85
75 mA
CMOS Standby Current (VCC = max, f = 0 MHz,
ISB2
20
20
20 mA
E ≥ VCC – 0.2 V, Vin ≤ VSS, or ≥ VCC – 0.2 V)
NOTES:
1. Reference AC Operating Conditions and Characteristics for input and timing (VIH/VIL, tr/tf, pulse level 0 to 3.0 V, VIH = 3.0 V).
2. All addresses transition simultaneously low (LSB) and then high (MSB).
3. Data states are all zero.
Notes
1, 2, 3
1, 2, 3
MCM6709BR
2
MOTOROLA FAST SRAM
|