|
ON Semiconductor |
MC12095
2.5 GHz Low Power
Prescaler With Stand-By
Mode
The MC12095 is a single modulus prescaler for low power
frequency division of a 2.5 GHz high frequency input signal.
MOSAIC Vt technology is utilized to achieve low power dissipation
of 24 mW at a minimum supply voltage of 2.7 V.
On–chip output termination provides output current to drive a
2.0 pF (typical) high impedance load. If additional drive is required
for the prescaler output, an external resistor can be added in parallel
from the OUT pin to GND to increase the output power. Care must be
taken not to exceed the maximum allowable current through the
output.
Divide ratio control input (SW) selects the required divide ratio of
÷2 or ÷4. Stand–By mode is available to reduce current drain to
100 mA typical when the standby pin SB is switched LOW disabling
the prescaler.
Features
• 2.5 GHz Toggle Frequency
• Supply Voltage 2.7 V to 5.5 Vdc
• Low Power 8.7 mA Typical
• Operating Temperature –40 to 85°C
• Divide by 2 or 4 Selected by the SW Pin
FUNCTIONAL TABLE
SW Divide Ratio
H2
L4
1. SW: H = (VCC – 0.4 V) to VCC; L = OPEN
2. SB: H = 2.0 V to VCC; L = GND to 0.8 V
C1
50 Ω
C2
VCC
IN SB
SW
IN OUT
GND
VCC = 2.7 to 5.5 V
C3
EXTERNAL
COMPONENTS
C1 = C2 = 1000 pF
C3 = 0.1 µF
C4 = 2.0 pF
C4
http://onsemi.com
MARKING
DIAGRAM
8
1
SO–8
D SUFFIX
CASE 751
8
12095
ALYW
1
A = Assembly Location
L = Wafer Lot
Y = Year
W = Work Week
PIN CONNECTIONS
IN 1
VCC 2
NC 3
OUT 4
8 IN
7 SB
6 SW
5 Gnd
(Top View)
ORDERING INFORMATION
Device
Package
Shipping
MC12095D
SO–8
96 Units/Rail
MC12095DR2
SO–8 2500 Tape & Reel
Figure 1. AC Test Circuit
© Semiconductor Components Industries, LLC, 2001
November, 2001 – Rev. 5
1
Publication Order Number:
MC12095/D
MC12095
MAXIMUM RATINGS
Rating
Power Supply Voltage, Pin 2
Operating Temperature Range
Storage Temperature Range
Maximum Output Current, Pin 4
NOTE: ESD data available upon request.
Symbol
VCC
TA
Tstg
IO
Value
–0.5 to 6.0
–40 to 85
–65 to 150
8.0
Unit
Vdc
°C
°C
mA
ELECTRICAL CHARACTERISTICS (VCC = 2.7 to 5.5 V; TA = –40 to 85°C, unless otherwise noted.)
Characteristic
Symbol Min Typ
Toggle Frequency (Sine Wave)
Supply Current
Stand–By Current
ft 500 3.0
ICC – 8.7
ISB – 100
Stand–By Input HIGH (SB)
Stand–By Input LOW (SB)
Divide Ratio Control Input HIGH (SW)
Divide Ratio Control Input LOW (SW)
Output Voltage Swing (2pF Load)
500–1000 MHz Input
1000–1500 MHz Input
1500–2500 MHz Input
VIH1
VIL1
VIH2
VIL2
VOUT
2.0
GND
VCC – 0.4
OPEN
800
400
200
–
–
VCC
OPEN
–
450
250
Input Voltage Sensitivity
VIN 200 –
Max
2.5
14
200
VCC + 0.5 V
0.8
VCC + 0.5 V
OPEN
–
–
–
1000
Unit
GHz
mA
µA
V
V
V
mVpp
mVpp
0
–10
–20
–30
–40
500
700 900 1100 1300 1500 1700 1900 2100 2300
Input Frequency (MHz)
(Divide By 2 Mode, T = 25°C, VCC = 2.7 V)
Figure 2. Typical Minimum Input Sensitivity versus Input Frequency
2500
http://onsemi.com
2
|