|
ROHM Semiconductor |
Datasheet
Power Management LSI
for Mobile Phone
BD71801GWL
General Description
The BD71801GWL is an integrated Power Management
LSI available in a small 80-pins 0.4mm-pitch 3.8mm-by-
3.8mm Wafer-level CSP package, which is designed to
meet demands for space-constrained Smart phones.
The device provides 5-Buck Converters.
The device also includes 12 general-purpose LDOs
providing a wide range of voltage and current
capabilities.
All Buck Converters and LDOs are fully controllable by
the I2C interface. The BD71801GWL is very easy to use
in any mobile platforms.
Features
5-Channel High Efficiency Step-down Converters.
(Adjustable Voltage Options by I2C)
(Switching frequency 2MHz(TYP))
All Buck Converters Support PFM/PWM Auto Mode.
12-Channel LDOs are Programmable to Voltage
Options by I2C.
LDOs and all Buck Converters Power ON/OFF
Control Enabled by I2C Interface or External pin.
2ch NMOS output LDOs (LDO11, 12) for Optimized
Efficiency.
Power ON/OFF Sequence.
Support TCXO Buffer (26MHz) and 32KHz crystal
oscillator.
I2C Compatible Interface.
( I2C Clock Support : Full Speed Mode 400kHz)
(Device Address is “1001011”,”1001100”)
Applications
Smart Phones
Tablets
Mobile Router
Data Transmitter
Key Specifications
Input Voltage Range:
Output Voltage Range:
Switching Frequency:
OFF Current:
Operating Temperature Range:
2.6V to 5.5V
1.0V to 3.4V
2.0MHz(Typ)
0.3μA (Typ)
-35℃ to +85℃
Package
UCSP50L3C
W(Typ) x D(Typ) x H(Max)
3.80mm x 3.80mm x 0.57mm
○Product structure:Silicon monolithic integrated circuit
.www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111・14・001
○This product is not designed protection against radioactive rays
1/75
TSZ02201-0B1B0AB00010-1-2
18.Nov.2013 Rev.002
BD71801GWL
Datasheet
Absolute Maximum Ratings(Ta=25C)
Parameter
Symbol
Rating
Unit
Maximum Supply Voltage 1
(VBATREF,VBAT, VIN1)
VBATMAX
7.0
V
Maximum Supply Voltage 2
(PBAT1,2,3,4,5)
VPBATMAX
7.0
V
Maximum Supply Voltage 3
(VIN2 )
VIN2MAX
4.2
V
Maximum Input Voltage 1
(OUT1, OUT2, OUT3, OUT4, OUT5,
OUT6,
OUT7, OUT8, OUT9, OUT10,
LX1, LX2, LX3, LX4, LX5,
PSET, ADRS, EN_O7, PWRON,
VINMAX1
7.0
V
PWRHOLD, POR, TCXO_IN,
OSC_IN, DVDD(Note1),
OSC_OUT, SIMRSTIN, SIMCLKIN,
SIMIODBB, SIMIO)
Maximum Input Voltage 2
(SDA, SCL)
VINMAX2
DVDD + 0.3
V
Maximum Input Voltage 3
(OUT11,12, REFC)
Power Dissipation
VINMAX3
Pd
VIN2MAX+ 0.3
1.38(Note 2)
V
W
Operating Temperature Range
Topr
-35 ~ +85
C
Storage Temperature Range
Tstg
-55 ~ +125
C
(Note 1) The DVDD Voltage must be under the Battery voltage VBAT, PBAT anytimes.
(Note 2) Derate by 13.8mW/ when operation above Ta=25 (when mounted in ROHM’s standard board(54mm × 62mm)).
Caution: Operation the IC over the absolute maximum ratings may damage the IC. In addition, it is impossible to predict all destructive situations such as
short-circuit modes, open circuit modes, etc. Therefore, it is important to consider circuit protection measures, likes adding a fuse, in case the IC
is operated in a special mode exceeding the absolute maximum ratings.
Recommended Operating Conditions (Ta=25C)
Parameter
Symbol
Range
VBAT Voltage
VBAT
2.70 ~ 5.50 (Note3)
PBAT Voltage
VPBAT
2.70 ~ 5.50 (Note3)
VIN1 Voltage
VIN1
2.70 ~ 5.50 (Note4)
VIN2 Voltage
VIN2
1.40 ~ 1.80 (Note5)
(Note 3) Whenever the VBAT or PBAT or VIN1 or VIN2 voltage is under the LDO, SWREG output voltage,
or under certain levels, the LDO and SWREG output is not guaranteed to meet its published specifications.
It is necessary to supply the same voltage to PBAT and VBAT.
(Note 4) To achieve the best efficiency performance, SWREG5 output is recommended to be connected to VIN1 externally.
(Note 5) To achieve the best efficiency performance, SWREG4 output is recommended to be connected to VIN2 externally.
Unit
V
V
V
V
○Product structure:Silicon monolithic integrated circuit
.www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
○This product is not designed protection against radioactive rays
2/75
TSZ02201-0B1B0AB00010-1-2
18.Nov.2013 Rev.002
|