|
Micrel Semiconductor |
MIC5162
Dual Regulator Controller for DDR3
GDDR3/4/5 Memory and High-Speed
Bus Termination
General Description
Features
The MIC5162 is a dual regulator controller designed for
high speed bus termination. It offers a simple, low-cost
JEDEC compliant solution for terminating high-speed, low-
voltage digital buses (i.e. DDR, DDR2, DDR3, SCSI, GTL,
SSTL, HSTL, LV-TTL, Rambus, LV-PECL, LV-ECL, etc).
The MIC5162 controls two external N-Channel MOSFETs
to form two separate regulators. It operates by switching
between either the high-side MOSFET or the low-side
MOSFET depending upon whether the current is being
sourced to the load or sunk by the regulator.
Designed to provide a universal solution for bus
termination regardless of input voltage, output voltage, or
load current. The desired MIC5162 output voltage can be
programmed by forcing the reference voltage externally to
desired voltage.
The MIC5162 operates from an input of 1.35V to 6V, with
a second bias supply input required for operation. It is
available in a tiny MSOP-10 package with operating
junction temperature range of -40°C to +125°C.
• Input voltage range: 1.35V to 6V
• Up to 7A VTT Current
• Tracking programmable output
• Wide bandwidth
• Logic controlled enable input
• Requires minimal external components
• DDR, DDR2, DDR3, memory termination
• -40°C < TJ < +125°C
• JEDEC Compliant Bus Termination for SCSI, GTL,
SSTL, HSTL, LV-TTL, Rambus, LV-PECL, LV-ECL, etc
• Tiny MSOP-10 package
Applications
• Desktop Computers
• Notebook computers
• Communication systems
Data sheets and support documentation can be found on • Video cards
Micrel’s web site at: www.micrel.com.
• DDR/DDR2/DDR3 memory termination
____________________________________________________________________________________________________________
Typical Application
Typical SSTL-2 Application
(Two MOSFETs Support a 3.5A Application)
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
March 2010
M9999-033110
Micrel, Inc.
MIC5162
Ordering Information
Part Number
Temperature Range
Package
MIC5162YMM
–40° to +125°C
10-Pin MSOP
Note: MSOP is a Green RoHS compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free.
Lead Finish
Pb-Free
Pin Configuration
10-Pin MSOP (MM)
Pin Description
Pin Number
1
2
Pin Name
VCC
EN
3 VDDQ
4 VREF
5 GND
6 FB
7 COMP
8 LD
9 HD
10 NC
Pin Function
Bias Supply Input. Apply 3V-6V to this input for internal bias to the controller.
Enable (Input): CMOS compatible input. Logic high = enable, logic low = shutdown.
The enable pin can be tied directly to VDDQ or VCC for functionality. Do not float the
enable pin. Floating this pin causes the enable to be in an undetermined state.
Input Supply Voltage.
Reference voltage equal to half of VDDQ. For internal use only.
Ground.
Feedback input to the internal error amplifier.
Compensation (Output): Connect a capacitor and resistor from COMP pin to
feedback pin for compensation of the internal control loop.
Low-side drive: Connects to the Gate of the external low-side MOSFET.
High-side drive: Connects to the Gate of the external high-side MOSFET.
Not internally connected.
March 2010
2 M9999-033110
|