|
ATMEL Corporation |
www.DataSheet4U.com
Features/Benefits
• Very Low Power Consumption in Active, Power-down and Sleep Mode
• 2-Kbyte ROM, 256 × 4-bit RAM
• 12 Bi-directional I/Os
• Up to 6 External/Internal Interrupt Sources
• Multifunction Timer/Counter
• Programmable System-clock with Prescaler and Five Different Clock Sources
• Wide Supply-voltage Range (1.8 V to 6.5 V)
• Very Low Sleep Current (< 1 µA)
• Synchronous Serial Interface (2-wire, 3-wire)
• Watchdog, POR and Brown-out Function
• Voltage Monitoring Inclusive Lo_BAT Detection
• Flash Controller ATAM893 available (SSO20)
Description
The ATAR080 is a member of Atmel’s family of 4-bit single-chip microcontrollers. It
contains ROM, RAM, parallel I/O ports, one 8-bit programmable multifunction
timer/counter with modulator function, voltage supervision, interval timer with watch-
dog function and a sophisticated on-chip clock generation with external clock input,
integrated RC-, 32-kHz and 4-MHz crystal-oscillators.
Figure 1. Block Diagram
VSS VDD
NRST/
OSC1 OSC2
Low-current
Microcontroller
for Wireless
Communication
ATAR080
BP20/NTE
BP21
BP22
BP23
Brown-out
protect RESET
Voltage Monitor
External input
VMI
RC Crystal External
oscillators oscillators clock input
Clock management
ROM
RAM
2 K × 8 bit 256 × 4 bit
MARC4
4-bit CPU core
I/O bus
UTCM
Timer 1
interval- and
watchdog timer
Timer 2
8/12-bit timer
with modulator
SSI
Serial interface
T2I
T2O
SD
SC
Data direction +
alternate function
Port 4
Data direction +
interrupt control
Port 5
BP40 BP42
INT3 T2O
SC
BP41 BP43
VMI INT3
T2I SD
BP50 BP52
INT6 INT1
BP51 BP53
INT6 INT1
Rev. 4675D–4BMCU–12/04
Pin Configuration
Figure 2. Pinning SSO20
VDD
BP40/INT3/SC
BP53/INT1
BP52/INT1
BP51/INT6
BP50/INT6
OSC1
NRST/OSC2
NC
NC
1
2
3
4
5
6
7
8
9
10
20 VSS
19 BP43/INT3/SD
18 BP42/T2O
17 BP41/VMI/T2I
16 BP23
15 BP22
14 BP21
13 BP20/NTE
12 NC
11 NC
Pin Description
Pin
VDD
VSS
NC
NC
BP20
BP21
BP22
BP23
BP40
BP41
BP42
BP43
BP50
BP51
BP52
BP53
NC
NC
OSC1
NRST/
OSC2
Type
–
–
–
–
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
–
–
I
I/O
O
Function
Supply voltage
Circuit ground
Not connected
Not connected
Bi-directional I/O line of Port 2.0
Bi-directional I/O line of Port 2.1
Bi-directional I/O line of Port 2.2
Bi-directional I/O line of Port 2.3
Bi-directional I/O line of Port 4.0
Bi-directional I/O line of Port 4.1
Bi-directional I/O line of Port 4.2
Bi-directional I/O line of Port 4.3
Bi-directional I/O line of Port 5.0
Bi-directional I/O line of Port 5.1
Bi-directional I/O line of Port 5.2
Bi-directional I/O line of Port 5.3
Not connected
Not connected
Oscillator input
Reset input/output
Oscillator output
Alternate Function
–
–
–
–
NTE test mode enable, see section “Master Reset”
–
–
–
SC serial clock or INT3 external interrupt input
VMI voltage monitor input or T2I external clock input
Timer 2
T2O Timer 2 output
SD serial data I/O or INT3-external interrupt input
INT6 external interrupt input
INT6 external interrupt input
INT1 external interrupt input
INT1 external interrupt input
–
–
4-MHz crystal input or 32-kHz crystal input or external
clock input or external trimming resistor input
4-MHz crystal output or 32-kHz crystal output or
NRST (mask option) or external clock input
Pin No.
SSO20
1
20
10
11
13
14
15
16
2
17
18
19
6
5
4
3
9
12
7
8
Reset
State
NA
NA
–
–
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
–
–
Input
NA
2 ATAR080
4675D–4BMCU–12/04
|