S6E1B8 판매점 - Microcontroller

S6E1B8 반도체 회로 부품 판매점

Microcontroller

Cypress Semiconductor

PRELIMINARY

S6E1B8 Series

32-bit ARM® Cortex®-M0+

FM0+ Microcontroller

The S6E1B8 Series is a series of highly integrated 32-bit microcontrollers designed for embedded controllers aiming at low power

consumption and low cost. This series has the ARM Cortex-M0+ Processor with on-chip Flash memory and SRAM, and consists of

peripheral functions such as various timers, LCD controller (LCDC), AES, ADC and communication interfaces (UART, CSIO (SPI),

I2C, I2S, Smart Card, and USB). The products which are described in this data sheet are placed into TYPE2-M0+ product categories

in "FM0+ Family Peripheral Manual".

Features

32-bit ARM Cortex-M0+ Core

Processor version: r0p1

Maximum operating frequency: 40.8 MHz

Nested Vectored Interrupt Controller (NVIC): 1 NMI

(non-maskable interrupt) and 24 peripheral interrupt with 4

selectable interrupt priority levels

24-bit System timer (Sys Tick): System timer for OS task

management

Bit Band Operation

Compatible with Cortex-M3 bit band operation.

On-Chip Memory

Flash memory

 Up to 512 K+48 Kbytes

 Dual bank:

 upper bank : 512 Kbytes(64 Kbytes x 8)

 lower bank : 48 Kbytes(8 Kbytes x 6)

 Read cycle: 0 wait-cycle

 Security function for code protection

SRAM

The on-chip SRAM of this series has one independent SRAM .

 Up to SRAM: 60 K+4 Kbytes

 4Kbytes: can retain value in Deep Standby Mode

USB Interface

USB interface is composed of Device and Host

PLL for USB is built-in, USB clock can be generated by

multiplication of Main clock.

USB Device

 USB 2.0 Full-Speed supported

 Max 6 EndPoint supported

• EndPoint 0 is control transfer

• EndPoint 1, 2 can be selected Bulk-transfer,

Interrupt-transfer or Isochronous-transfer

• EndPoint 3 to 5 can select Bulk-transfer or

Interrupt-transfer

• EndPoint 1 to 5 comprise Double Buffer

• The size of each EndPoint is according to the follows

• EndPoint 0, 2 to 5 : 64 bytes

• EndPoint 1 : 256 bytes

USB host

 USB 2.0 Full/Low-Speed supported

 Bulk-transfer, Interrupt-transfer and Isochronous-transfer

support

 USB Device connected/disconnected automatically detect

 IN/OUT token handshake packet automatically

 Max 256-byte packet-length supported

 Wake-up function supported

LCD Controller (LCDC)

 Selectable from 44 SEG × 4 COM (Max) or 40 SEG × 8

COM (Max)

 Internal Charge pump can generate 4.6 V at most

 Internal divide resistor is contained (selectable from 10 k

or 100 k for the resistor value)

 LCD drive power supply (bias) pin (VV4 to VV0)

 Interrupt function synchronized with the LCD module frame

frequency

 With blinking function

 Inverted display function

Multi-Function Serial Interface (Max 8channels)

128 bytes with Tx/Rx FIFO in all channels (The number of

FIFO steps varies depending on the settings of the

communication mode or bit length.)

The operation mode of each channel can be selected from

one of the following.

 UART

 CSIO (CSIO is known to many customers as SPI)

 I2C

UART

 Full duplex double buffer

 Parity can be enabled or disabled.

 Built-in dedicated baud rate generator

 External clock available as a serial clock

 Various error detection functions (parity errors, framing

errors, and overrun errors)

CSIO (also known as SPI)

 Full duplex double buffer

 Built-in dedicated baud rate generator

 Overrun error detection function

 Serial chip select function (ch1 and ch3 only)

 Data length: 5 to 16 bits

Cypress Semiconductor Corporation

Document Number: 001-99223 Rev.**

• 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600

Revised August 31, 2015

PRELIMINARY

S6E1B8 Series

I2C

 Standard-mode (Max: 100 kbps) supported / Fast-mode

(Max 400 kbps) supported.

I2S

 Using CSIO (ch.5, ch.6) and I2S clock generator

 Supports two transfer protocol

• I2S

• MSB-justified

 Master mode only

Descriptor System Data Transfer Controller (DSTC)

(64 Channels)

The DSTC can transfer data at high-speed without going via

the CPU. The DSTC adopts the Descriptor

system and, following the specified contents of the

Descriptor that has already been constructed on the

memory, can access directly the memory / peripheral device

and performs the data transfer operation.

It supports the software activation, the hardware activation,

and the chain activation functions

A/D Converter (Max: 24 Channels)

12-bit A/D Converter

 Successive approximation type

 Conversion time: 2.0 μs @ 2.7 V to 3.6 V

 Priority conversion available (2 levels of priority)

 Scan conversion mode

 Built-in FIFO for conversion data storage (for scan

conversion: 16 steps, for priority conversion: 4 steps)

Base Timer (Max: 8 Channels)

The operation mode of each channel can be selected from one

of the following.

16-bit PWM timer

16-bit PPG timer

16/32-bit reload timer

16/32-bit PWC timer

General-Purpose I/O Port

This series can use its pin as a general-purpose I/O port when

it is not used for an external bus or a peripheral function. All

ports can be set to fast general-purpose I/O ports or slow

general-purpose I/O ports. In addition, this series has a port

relocate function that can set to which I/O port a peripheral

function can be allocated.

All ports are Fast GPIO which can be accessed by 1cycle

Capable of controlling the pull-up of each pin

Capable of reading pin level directly

Port relocate function

Up to 102 fast general-purpose I/O ports @120-pin package

Certain ports are 5 V tolerant.

See 4. List of Pin Functions and 5. I/O Circuit Type for the

corresponding pins.

Dual Timer (32-/16-bit Down Counter)

The Dual Timer consists of two programmable 32-/16-bit down

counters. The operation mode of each timer channel can be

selected from one of the following.

Free-running mode

Periodic mode (= Reload mode)

One-shot mode

Multi-Function Timer

The Multi-function Timer consists of the following blocks.

16-bit free-run timer × 3 channels

Input capture × 4 channels

Output compare × 6 channels

ADC start compare × 6 channel

Waveform generator × 3 channels

16-bit PPG timer × 3 channels

IGBT mode is contained.

The following function can be used to achieve the motor

control.

PWM signal output function

DC chopper waveform output function

Dead time function

Input capture function

ADC start function

DTIF (motor emergency stop) interrupt function

Real-Time Clock (RTC with Vbat)

The Real-time Clock counts

year/month/day/hour/minute/second/day of the week from year

01 to year 99.

The RTC can generate an interrupt at a specific time

(year/month/day/hour/minute/second/day of the week) and

can also generate an interrupt in a specific year, in a specific

month, on a specific day, at a specific hour or at a specific

minute.

It has a timer interrupt function generating an interrupt upon

a specific time or at specific intervals.

It can keep counting while rewriting the time.

It can count leap years automatically.

Document Number: 001-99223 Rev.**

Page 2 of 128

PDF 파일 내의 페이지 : 총 30 페이지

제조업체: Cypress Semiconductor

( cypress )

S6E1B8 controller

데이터시트 다운로드 :

[ S6E1B8.PDF ]

[ S6E1B8 다른 제조사 검색 ]

국내 전력반도체 판매점

상호 : 아이지 인터내셔날

전화번호 : 051-319-2877

[ 홈페이지 ]

IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈

( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )

전력반도체 문의 : 010-3582-2743

일반적인 전자부품 판매점

디바이스마트

IC114

엘레파츠

ICbanQ

Mouser Electronics

DigiKey Electronics

Element14

S6E1B8 반도체 회로 부품 판매점

Microcontroller

국내 전력반도체 판매점

일반적인 전자부품 판매점

관련 데이터시트