|
ETC |
PI74FCT16P37I47/146F23C74T/11662H373744TT
PI74FCT162374T12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901211623-4B56I7T890R12E34G567I8S90T12E34R56S789(031-2S12T34A567T89E01)2
PI74FCT162H374T
1122334455667788990011223344556677889900112233445566778899001122112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900112233445566778899001122112233445566778899001122
Fast CMOS 16-Bit
Registers (3-State)
Product Features:
Common Features:
• PI74FCT16374T,PI74FCT162374T,andPI74FCT162H374T
are high-speed,
low power devices with high current drive.
• Vcc=5V±10%
• Hysteresis on all inputs
• Packages available:
– 48-pin 240 mil wide plastic TSSOP (A)
– 48-pin 300 mil wide plastic SSOP (V)
PI74FCT16374T Features:
• High output drive: IOH = –32 mA; IOL = 64 mA
• Power off disable outputs permit "live insertion"
• Typical VOLP (Output Ground Bounce) < 1.0V
at VCC = 5V, TA = 25°C
PI74FCT162374T Features:
• Balanced output drivers: ±24 mA
• Reduced system switching noise
• Typical VOLP (Output Ground Bounce) < 0.6V
at VCC = 5V, TA = 25°C
PI74FCT162H374T Features:
• Bus Hold retains last active bus state during 3-state
• Eliminates the need for external pull-up resistors
Logic Block Diagram
Product Description:
Pericom Semiconductor’s PI74FCT series of logic circuits are
produced in the Company’s advanced 0.6 micron CMOS technology,
achieving industry leading speed grades.
The PI74FCT16374T, PI74FCT162374T, and PI74FCT162H374T
are 16-bit octal registers designed with 16 D-type flip-flops with a
buffered common clock and 3-state outputs. The Output Enable
(xOE) and clock (xCLK) controls are organized to operate as
two 8-bit registers or one 16-bit register. When OE is HIGH, the
outputs are in the high impedance state. Input data meeting the
setup and hold time requirements of the D inputs is transferred to
the O outputs on the LOW-to-HIGH transition of the clock input.
The PI74FCT16374T output buffers are designed with a Power-Off
disable allowing “live insertion” of boards when used as backplane
drivers.
The PI74FCT162374T has ±24 mA balanced output drivers. It is
designed with current limiting resistors at its outputs to control the
output edge rate resulting in lower ground bounce and undershoot.
This eliminates the need for external terminating resistors for most
interface applications.
The PI74FCT162H374T has “Bus Hold” which retains the input’s
last state whenever the input goes to high-impedance preventing
“floating” inputs and eliminating the need for pull-up/down
resistors.
1OE
1CLK
1D0
D
C
2OE
2CLK
2D0
1O0
D
C
2O0
TO 7 OTHER CHANNELS
TO 7 OTHER CHANNELS
1 PS2034A 03/28/01
PI74FCT16374/162374/162H374T
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901211623-4B56I7T890R12E34G567I8S90T12E34R56S789(031-2S12T34A567T89E01)2
Product Pin Description
Pin Name
xOE
xCLK
xDx
xOx
GND
VCC
Description
3-State Output Enable Inputs (Active LOW)
Clock Inputs
Inputs(1)
3-State Outputs
Ground
Power
Note: 1. For the PI74FCT162H374T, these pins have “Bus
Hold.” All other pins are standard, outputs, or I/Os.
Product Pin Configuration
1OE
1O0
1O1
GND
1O2
1O3
VCC
1O4
1O5
GND
1O6
1O7
2O0
2O1
GND
2O2
2O3
VCC
2O4
2O5
GND
2O6
2O7
2OE
1 48
2 47
3 46
4 45
5 44
6 43
7 42
8 41
9 40
10 48-PIN 39
11 V48 38
12 A48 37
13 36
14 35
15 34
16 33
17 32
18 31
19 30
20 29
21 28
22 27
23 26
24 25
1CLK
1D0
1D1
GND
1D2
1D3
VCC
1D4
1D5
GND
1D6
1D7
2D0
2D1
GND
2D2
2D3
VCC
2D4
2D5
GND
2D6
2D7
2CLK
Truth Table(1)
Function
High-Z
Load Register
XDX
X
X
L
H
L
H
Inputs
XCLK
L
H
↑
↑
↑
↑
XOE
H
H
L
L
H
H
Outputs
XOX
Z
Z
L
H
Z
Z
Note:
1. H = High Voltage Level
L = Low Voltage Level
X = Don’t Care
Z = High Impedance
↑ = LOW-to-HIGH transition
2 PS2034A 03/28/01
|