A29800TV-55 반도체 회로 부품 판매점
1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only/ Boot Sector Flash Memory
|
|
 AMIC Technology |
A29800 Series
Preliminary
1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only,
Boot Sector Flash Memory
Features
n 5.0V ± 10% for read and write operations
n Access times:
- 55/70/90 (max.)
n Current:
- 28mA read current (word mode)
- 20 mA typical active read current (byte mode)
- 30 mA typical program/erase current
- 1 µA typical CMOS standby
n Flexible sector architecture
- 16 Kbyte/ 8 KbyteX2/ 32 Kbyte/ 64 KbyteX15 sectors
- 8 Kword/ 4 KwordX2/ 16 Kword/ 32 KwordX15 sectors
- Any combination of sectors can be erased
- Supports full chip erase
- Sector protection:
A hardware method of protecting sectors to prevent
any inadvertent program or erase operations within
that sector
n Top or bottom boot block configurations available
n Embedded Erase Algorithms
- Embedded Erase algorithm will automatically erase
the entire chip or any combination of designated
sectors and verify the erased sectors
- Embedded Program algorithm automatically writes
and verifies bytes at specified addresses
n Typical 100,000 program/erase cycles per sector
n 20-year data retention at 125°C
- Reliable operation for the life of the system
n Compatible with JEDEC-standards
- Pinout and software compatible with single-power-
supply Flash memory standard
- Superior inadvertent write protection
n Data Polling and toggle bits
- Provides a software method of detecting completion
of program or erase operations
n Erase Suspend/Erase Resume
- Suspends a sector erase operation to read data from,
or program data to, a non-erasing sector, then
resumes the erase operation
n Hardware reset pin (RESET )
- Hardware method to reset the device to reading array
data
n Package options
- 44-pin SOP or 48-pin TSOP (I)
General Description
The A29800 is a 5.0 volt only Flash memory organized as
1048,576 bytes of 8 bits or 524,288 words of 16 bits each. The
A29800 offers the RESET function. The 1024 Kbytes of data
are further divided into nineteen sectors for flexible sector erase
capability. The 8 bits of data appear on I/O0 - I/O7 while the
addresses are input on A1 to A18; the 16 bits of data appear on
I/O0~I/O15. The A29800 is offered in 44-pin SOP and 48-Pin
TSOP packages. This device is designed to be programmed in-
system with the standard system 5.0 volt VCC supply. Additional
12.0 volt VPP is not required for in-system write or erase
operations. However, the A29800 can also be programmed in
standard EPROM programmers.
The A29800 has the first toggle bit, I/O6, which indicates whether
an Embedded Program or Erase is in progress, or it is in the
Erase Suspend. Besides the I/O6 toggle bit, the A29800 has a
second toggle bit, I/O2, to indicate whether the addressed sector
is being selected for erase. The A29800 also offers the ability to
program in the Erase Suspend mode. The standard A29800
offers access times of 55, 70 and 90 ns, allowing high-speed
microprocessors to operate without wait states. To eliminate bus
contention the device has separate chip enable ( CE ), write
enable ( WE ) and output enable ( OE ) controls.
The device requires only a single 5.0 volt power supply for both
read and write functions. Internally generated and regulated
voltages are provided for the program and erase operations.
The A29800 is entirely software command set compatible with
the JEDEC single-power-supply Flash standard. Commands are
written to the command register using standard microprocessor
write timings. Register contents serve as input to an internal
state-machine that controls the erase and programming circuitry.
Write cycles also internally latch addresses and data needed for
the programming and erase operations. Reading data out of the
device is similar to reading from other Flash or EPROM devices.
Device programming occurs by writing the proper program
command sequence. This initiates the Embedded Program
algorithm - an internal algorithm that automatically times the
program pulse widths and verifies proper program margin.
Device erasure occurs by executing the proper erase command
sequence. This initiates the Embedded Erase algorithm - an
internal algorithm that automatically preprograms the array (if it
is not already programmed) before executing the erase
operation.
PRELIMINARY (May, 2001, Version 0.0)
1
AMIC Technology, Inc.
A29800 Series
During erase, the device automatically times the erase pulse
widths and verifies proper erase margin.
The host system can detect whether a program or erase
operation is complete by reading the I/O7 ( Data Polling) and
I/O6 (toggle) status bits. After a program or erase cycle has
been completed, the device is ready to read array data or
accept another command.
The sector erase architecture allows memory sectors to be
erased and reprogrammed without affecting the data
contents of other sectors. The A29800 is fully erased when
shipped from the factory.
The hardware sector protection feature disables operations
for both program and erase in any combination of the
Pin Configurations
sectors of memory. This can be achieved via programming
equipment.
The Erase Suspend feature enables the user to put erase on
hold for any period of time to read data from, or program
data to, any other sector that is not selected for erasure.
True background erase can thus be achieved.
Power consumption is greatly reduced when the device is
placed in the standby mode.
The hardware RESET pin terminates any operation in
progress and resets the internal state machine to reading
array data.
n SOP
n TSOP (I)
RY/BY
A18
A17
A7
A6
A5
A4
A3
A2
A1
A0
CE
VSS
OE
I/O0
I/O8
I/O1
I/O9
I/O2
I/O10
I/O3
I/O11
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
44 RESET
43 WE
42 A8
41 A9
40 A10
39 A11
38 A12
37 A13
36 A14
35 A15
34 A16
33 BYTE
32 VSS
31 I/O15 (A-1)
30 I/O7
29 I/O14
28 I/O6
27 I/O13
26 I/O5
25 I/O12
24 I/O4
23 VCC
A15
A14
A13
A12
A11
A10
A9
A8
NC
NC
WE
RESET
NC
NC
RY/BY
A18
A17
A7
A6
A5
A4
A3
A2
A1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
A29800V
48 A16
47 BYTE
46 VSS
45 I/O15 (A-1)
44 I/O7
43 I/O14
42 I/O6
41 I/O13
40 I/O5
39 I/O12
38 I/O4
37 VCC
36 I/O11
35 I/O3
34 I/O10
33 I/O2
32 I/O9
31 I/O1
30 I/O8
29 I/O0
28 OE
27 VSS
26 CE
25 A0
PRELIMINARY (May, 2001, Version 0.0)
2
AMIC Technology, Inc.
|
PDF 파일 내의 페이지 : 총 30 페이지
제조업체: AMIC Technology
( amic )
A29800TV-55 cmos
데이터시트 다운로드 :
[ A29800TV-55.PDF ]
[ A29800TV-55 다른 제조사 검색 ]
국내 전력반도체 판매점
상호 : 아이지 인터내셔날
전화번호 : 051-319-2877
[ 홈페이지 ]
IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈
( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )
전력반도체 문의 : 010-3582-2743
관련 데이터시트
A29800TV-55
1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only/ Boot Sector Flash Memory - AMIC Technology
