|
Intersil Corporation |
HFA1405
September 1998
File Number 3604.5
Quad, 560MHz, Low Power, Video
Operational Amplifier
The HFA1405 is a quad, high speed, low power current
feedback amplifier built with Intersil’s proprietary
complementary bipolar UHF-1 process.
These amplifiers deliver up to 560MHz bandwidth and
1700V/µs slew rate, on only 58mW of quiescent power. They
are specifically designed to meet the performance, power,
and cost requirements of high volume video applications.
The excellent gain flatness and differential gain/phase
performance make these amplifiers well suited for
component or composite video applications. Video
performance is maintained even when driving a back
terminated cable (RL = 150Ω), and degrades only slightly
when driving two back terminated cables (RL = 75Ω). RGB
applications will benefit from the high slew rates, and high
full power bandwidth.
The HFA1405 is a pin compatible, low power, high
performance upgrade for the popular Intersil HA5025, and
for the CLC414 and CLC415.
Ordering Information
TEMP.
PART NUMBER RANGE (oC)
PACKAGE
PKG.
NO.
HFA1405IB
-40 to 85 14 Ld SOIC
M14.15
HFA1405IP
-40 to 85 14 Ld PDIP
E14.3
HA5025EVAL
High Speed Op Amp DIP Evaluation Board
Pinout
HFA1405
(PDIP, SOIC)
TOP VIEW
OUT 1 1
-IN 1 2 -
+IN 1 3
V+ 4
+IN 2 5
-
-IN 2 6
OUT 2 7
14 OUT 4
- 13 -IN 4
12 +IN 4
11 V-
10 +IN 3
-
9 -IN 3
8 OUT 3
Features
• Low Supply Current . . . . . . . . . . . . . . . . . 5.8mA/Op Amp
• High Input Impedance . . . . . . . . . . . . . . . . . . . . . . . 1MΩ
• Wide -3dB Bandwidth (AV = +2) . . . . . . . . . . . . . . 560MHz
• Very Fast Slew Rate . . . . . . . . . . . . . . . . . . . . . . 1700V/µs
• Gain Flatness (to 50MHz) . . . . . . . . . . . . . . . . . . . . ±0.03dB
• Differential Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.02%
• Differential Phase . . . . . . . . . . . . . . . . . . . . 0.03 Degrees
• All Hostile Crosstalk (5MHz). . . . . . . . . . . . . . . . . . -60dB
• Pin Compatible Upgrade to HA5025, CLC414, and
CLC415
Applications
• Flash A/D Drivers
• Professional Video Processing
• Video Digitizing Boards/Systems
• Multimedia Systems
• RGB Preamps
• Medical Imaging
• Hand Held and Miniaturized RF Equipment
• Battery Powered Communications
• High Speed Oscilloscopes and Analyzers
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
HFA1405
Absolute Maximum Ratings TA = 25oC
Voltage Between V+ and V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11V
DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VSUPPLY
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V
Output Current (Note 2) . . . . . . . . . . . . . . . . .Short Circuit Protected
30mA Continuous
60mA ≤ 50% Duty Cycle
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3015.7) . . . 600V
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (oC/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
120
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100
Maximum Junction Temperature (Die) . . . . . . . . . . . . . . . . . . . 175oC
Maximum Junction Temperature (Plastic Package) . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC
(SOIC - Lead Tips Only)
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
2. Output is short circuit protected to ground. Brief short circuits to ground will not degrade reliability, however continuous (100% duty cycle) output
current must not exceed 30mA for maximum reliability.
Electrical Specifications VSUPPLY = ±5V, AV = +1, RF = 510Ω , RL = 100Ω , Unless Otherwise Specified
PARAMETER
(NOTE 4)
TEST TEMP.
TEST CONDITIONS LEVEL (oC)
HFA1405IB (SOIC)
MIN TYP MAX
HFA1405IP (PDIP)
MIN TYP MAX
INPUT CHARACTERISTICS
Input Offset Voltage
A 25 - 2 5 - 2 5
A Full - 3 8 - 3 8
Average Input Offset Voltage Drift
B Full - 1 10 - 1 10
Input Offset Voltage
Common-Mode Rejection Ratio
Input Offset Voltage
Power Supply Rejection Ratio
Non-Inverting Input Bias Current
∆VCM = ±1.8V
∆VCM = ±1.8V
∆VCM = ±1.2V
∆VPS = ±1.8V
∆VPS = ±1.8V
∆VPS = ±1.2V
A 25 45 48 - 45 48 -
A 85 43 46 - 43 46 -
A -40 43 46 - 43 46 -
A 25 48 52 - 48 52 -
A 85 46 48 - 46 48 -
A -40 46 48 - 46 48 -
A 25 - 6 15 - 6 15
A Full - 10 25 - 10 25
Non-Inverting Input Bias Current
Drift
B Full - 5 60 - 5 60
Non-Inverting Input Bias Current
Power Supply Sensitivity
Non-Inverting Input Resistance
Inverting Input Bias Current
∆VPS = ±1.8V
∆VPS = ±1.8V
∆VPS = ±1.2V
∆VCM = ±1.8V
∆VCM = ±1.8V
∆VCM = ±1.2V
A 25 - 0.5 1 - 0.5 1
A 85 - 0.8 3 - 0.8 3
A
-40 - 0.8 3
- 0.8 3
A 25 0.8 1.2 - 0.8 1.2 -
A 85 0.5 0.8 - 0.5 0.8 -
A -40 0.5 0.8 - 0.5 0.8 -
A 25 - 2 7.5 - 2 7.5
A Full - 5 15 - 5 15
Inverting Input Bias Current Drift
B
Full
-
60 200
-
60 200
Inverting Input Bias Current
Common-Mode Sensitivity
∆VCM = ±1.8V
∆VCM = ±1.8V
∆VCM = ±1.2V
A 25 - 3 6 - 3 6
A 85 - 4 8 - 4 8
A -40 - 4 8 - 4 8
UNITS
mV
mV
µV/oC
dB
dB
dB
dB
dB
dB
µA
µA
nA/oC
µA/V
µA/V
µA/V
MΩ
MΩ
MΩ
µA
µA
nA/oC
µA/V
µA/V
µA/V
2
|