|
Bytes |
1.5KE SERIES
1500 WATT PEAK POWER TRANSIENT VOLTAGE SUPPRESSORS
FEATURES
* 1500 Watts Surge Capability at 1ms
* Excellent clamping capability
* Low zener impedance
* Fast response time: Typically less than
1.0ps from 0 volt to BV min.
* Typical IR less than 1µA above 10V
* High temperature soldering guaranteed:
260 C / 10 seconds / .375"(9.5mm) lead
length, 5lbs.(2.3kg) tension
MECHANICAL DATA
* Case: Molded plastic
* Epoxy: UL 94V-0 rate flame retardant
* Lead: Axial leads, solderable per MIL-STD-202,
method 208 guranteed
* Polarity: Color band denotes cathode end
* Mounting position: Any
* Weight: 1.20 grams
VOLTAGE RANGE
6.8 to 440 Volts
1500 Watts Peak Power
5.0 Watts Steady State
DO-201
.210(5.3)
.188(4.8)
DIA.
1.0(25.4)
MIN.
.375(9.5)
.285(7.2)
.042(1.1)
.037(0.9)
DIA.
1.0(25.4)
MIN.
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating 25 C ambient temperature uniess otherwies specified.
Single phase half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
RATINGS
Peak Power Dissipation at TA=25 C, TP=1ms(NOTE 1)
Steady State Power Dissipation at TL=75 C
Lead Length .375"(9.5mm) (NOTE 2)
Peak Forward Surge Current at 8.3ms Single Half Sine-Wave
superimposed on rated load (JEDEC method) (NOTE 3)
Operating and Storage Temperature Range
SYMBOL
PPK
PD
IFSM
TJ, TSTG
NOTES:
1. Non-repetitive current pulse per Fig. 3 and derated above TA=25 C per Fig. 2.
2. Mounted on Copper Pad area of 0.8" X 0.8" (20mm X 20mm) per Fig.5.
3. 8.3ms single half sine-wave, duty cycle = 4 pulses per minute maximum.
VALUE
Minimum 1500
5.0
200
-55 to +175
DEVICES FOR BIPOLAR APPLICATIONS
1. For Bidirectional use C or CA Suffix for types 1.5KE6.8 thru 1.5KE440.
2. Electrical characteristics apply in both directions.
UNITS
Watts
Watts
Amps
C
138
RATING AND CHARACTERISTIC CURVES (1.5KE SERIES)
FIG.1-PEAK PULSE POWER DERATING CURVE
100
Non-Repetitive
Pulse Waveform
Shown in Fig. 3
TA=25 C
10
1.0
FIG.2-PULSE DERATING CURVE
100
75
50
25
0.1
0.1µs
1.0µs
10µs
100µs
td, PULSE WIDTH, sec.
1.0ms
10ms
FIG.3-PULSE WAVE FORM
150
tf=10µs
Peak Value
IPPM
100
TA=25 C
Pulse Width (td) is defined
as the point where the Peak
Current Deacys to 50% of Ipp
50
td
0 0 1.0
Half Value-IPPM
2
10/1000µsec Waveform
as Defined by R.E.A.
2.0
t, TIME, ms
e-kt
3.0
4.0
0
0 25 50 75 100 125 150 175
TA, AMBIENT TEMPERATURE ( C)
10000
1000
FIG.4-TYPICAL JUNCTION CAPACITANCE
TJ=25 C
f=1.0MHz
Vsig=50mVp-p
Measued at
Zero Bias
100 Measured at
Stand-Off
Voltage(VMW)
10
5.0
10 20
50 100
200
V(BR), BREAKDOWN VOLTAGE, VOLTS
500
FIG.5-STEADY STATE POWER DERATING CURVE
5.00
3.75
2.50
1.25
L=.375"(9.5mm)
20mm x 20mm x 1mm
Copper Heat Sink
(0.8" x 0.8" x .040")
0
0
25 50
75 100 125 150 175 200
TL, LEAD TEMPERATURE ( C)
FIG.6-MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT, UNIDIRECTIONAL
200
TJ=TJmax
8.3ms Single Half Sine-wave
JEDEC Method
100
50
UNIDIRECTIONAL ONLY
20
10
1
5 10
20
50 100
NUMBER OF CYCLES AT 60Hz
139
|