|
Diodes Incorporated |
Features
AP1186
1.5A ULTRA LOW DROPOUT POSITIVE ADJUSTABLE OR
FIXED-MODE REGULATOR
General Description
• Adjustable or Fixed output voltage 1.5V, 1.8V, 2.5V,
3.3V, 5.0V
• 0.5V Maximum Dropout voltage at 1.5A Load current
• Built-in Thermal Shutdown
• Output Current Limiting
• Fast transient response
• Good noise rejection
• Packages: TO220-5L, TO263-5L
• Lead Free Finish/RoHS Compliant for Lead Free
products (Note 1)
Ordering Information
AP1186 is a 1.5A regulator with extremely low dropout voltage.
This product is specifically designed to provide well-regulated
supply for applications requiring 2.8V or lower voltages from 3.3V
ATX power supplies where high efficiency of a switcher can be
achieved without the cost and complexity associated with a
switching regulator. One such application is the new graphic chip
sets that require anywhere from 2.4V to 2.7V supply.
AP 1186 X - X X X
Package
K5:TO263-5L
T5:TO220-5L
Vout
Blank : Adj
15 : 1.5V
18 : 1.8V
25 : 2.5V
33 : 3.3V
50 : 5.0V
Lead Free
L : Lead Free Package
Packing
-U : Tube
-13: Taping
Note: 1. RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7.
Device
Package
Code
Packaging
(Note 2)
Tube
Quantity
Part Number
Suffix
13” Tape and Reel
Quantity
Part Number
Suffix
AP1186T5
Lead-free
AP1186K5
T5 TO220-5L 50
K5 TO263-5L 50
-U NA NA
-U 800/Tape & Reel -13
Lead-free
Note: 2. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at
http://www.diodes.com/datasheets/ap02001.pdf.
Typical Application
AP1186 Rev. 1
3V
+
470uF
Vin
VVcoturl
GNt D
Vsense
5
4
3
2
1
5V
+
470uF
2.5
V
/1.5A
+
470uF
1 of 9
www.diodes.com
MARCH 2007
© Diodes Incorporated
Block Diagram
AP1186
1.5A ULTRA LOW DROPOUT POSITIVE ADJUSTABLE OR
FIXED-MODE REGULATOR
Vin
Vctrl
+
+
CURRENT
LIMIT
-
THERMAL
SHUTDOWN
1.25V +
+
Vout
Vsense
Adj
Package Connect Diagram
5 PIN TO263
FRONT VIEW
5 Vin
4 Vctrl
3 Vout
2 Adj(GND)
1 Vsense
Tab is Vout
5 PIN TO220
FRONT VIEW
5
4
3
2
1
Tab is Vout
Vin
Vctrl
Vout
Adj(GND)
Vsense
Pin Descriptions
Name I/O
Description
Vsense
I
This pin is the positive side of the reference that allows remote load sensing to achieve excellent load
regulation. A minimum of 10uF capacitor must be connected from this pin to ground to insure stability.
Adj
(GND)
Vout
Vctrl
Vin
A resistor divider from this pin to the Vout pin and ground sets the output voltage.
(GND only for fixed mode)
O
The output of the regulator. A minimum of 100uF capacitor must be connected from this pin to ground
to insure stability.
This pin is the supply pin for the internal control circuit as well as the base drive for the pass transistor.
I This pin must always by higher than the Vout pin in order for the device to regulate. A minimum of
100uF capacitor must be connected from this pin to ground to insure stability.
The input of the regulator. Typically a large storage capacitor is connected from this pin to ground to
I insure that the input voltage does not sag below the minimum dropout voltage during the load
transient response. This pin must always be higher than Vout in order for the device to regulate.
AP1186 Rev. 1
2 of 9
www.diodes.com
MARCH 2007
© Diodes Incorporated
|