|
|
PDF TSOP75536 Data sheet ( Hoja de datos )
| Número de pieza | TSOP75536 | |
| Descripción | IR Receiver Modules | |
| Fabricantes | Vishay | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TSOP75536 (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
|
No Preview Available !
www.vishay.com
TSOP753.., TSOP755..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
4
3
2
1
20953
MECHANICAL DATA
Pinning:
1, 4 = GND, 2 = VS, 3 = OUT
ORDERING CODE
Taping:
TSOP75...TT - top view taped
TSOP75...TR - side view taped
FEATURES
• Very low supply current
• Photo detector and preamplifier in one package
• Compatible also with short burst dataformats
• Supply voltage: 2.5 V to 5.5 V
• Improved immunity against ambient light
• Capable of side or top view
• Two lenses for high sensitivity and wide
receiving angle
• Insensitive to supply voltage ripple and noise
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
DESCRIPTION
The TSOP753.., TSOP755.. series are a two lens
miniaturized receiver module for infrared remote control
systems. One PIN diode per lens and a preamplifier are
assembled on a leadframe, the epoxy lens cap contains an
IR filter.
The TSOP753..series is optimized to suppress almost all
spurious pulses from energy saving lamps like CFLs. AGC3
may also suppress some data signals if continuously
transmitted.
The TSOP755.. series contain a very robust AGC5. This
series should only be used for critically noisy environments.
This component has not been qualified according to
automotive specifications.
PARTS TABLE
AGC
30 kHz
33 kHz
Carrier
36 kHz
frequency 38 kHz
40 kHz
56 kHz
Package
Pinning
Dimensions (mm)
Mounting
Application
Best remote control code
NOISY ENVIRONMENTS
AND SHORT BURSTS (AGC3)
VERY NOISY ENVIRONMENTS
AND SHORT BURSTS (AGC5)
TSOP75330
TSOP75530
TSOP75333
TSOP75533
TSOP75336 (1)
TSOP75536
TSOP75338 (2)(3)(4)(5)
TSOP75538
TSOP75340
TSOP75540
TSOP75356
TSOP75556
Heimdall
1, 4 = GND, 2 = VS, 3 = OUT
6.8 W x 3.0 H x 3.2 D
SMD
Remote control
(1) MCIR (2) Mitsubishi (3) RECS-80 Code (4) r-map (5) XMP-1, XMP-2
Rev. 1.5, 22-Jul-16
1 Document Number: 82495
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
1 page  
www.vishay.com
SUITABLE DATA FORMAT
The TSOP753.., TSOP755.. series are designed to suppress
spurious output pulses due to noise or disturbance signals.
Data and disturbance signals can be distinguished by the
devices according to carrier frequency, burst length and
envelope duty cycle. The data signal should be close to the
band-pass center frequency (e.g. 38 kHz) and fulfill the
conditions in the table below.
When a data signal is applied to the TSOP753.. and
TSOP755.. in the presence of a disturbance signal, the
sensitivity of the receiver is reduced to insure that no
spurious pulses are present at the output. Some examples
of disturbance signals which are suppressed are:
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signals at any frequency
• Strongly or weakly modulated pattern from fluorescent
lamps with electronic ballasts (see Fig. 14 or Fig. 15)
TSOP753.., TSOP755..
Vishay Semiconductors
0
16920
5 10 15
Time (ms)
20
Fig. 14 - IR Disturbance from Fluorescent Lamp
with Low Modulation
0
16921
5 10 15
Time (ms)
20
Fig. 15 - IR Disturbance from Fluorescent Lamp
with High Modulation
Minimum burst length
After each burst of length
a minimum gap time is required of
For bursts greater than
a minimum gap time in the data stream is
needed of
Maximum number of continuous short
bursts/second
MCIR code
RCMM code
XMP-1, XMP-2 code
Suppression of interference from fluorescent
lamps
TSOP753..
6 cycles/burst
6 to 35 cycles
≥ 10 cycles
35 cycles
> 4 x burst length
2000
Preferred
Preferred
Preferred
Mild and complex disturbance
patterns are suppressed (example:
signal pattern of Fig. 14 and Fig. 15)
Note
• For data formats with long bursts please see the datasheet for TSOP752.., TSOP754..
TSOP755..
6 cycles/burst
6 to 24 cycles
≥ 10 cycles
24 cycles
> 25 ms
2000
Yes
Yes
Yes
Critical disturbance
patterns are suppressed,
e.g. highly dimmed LCDs
Rev. 1.5, 22-Jul-16
5 Document Number: 82495
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
5 Page 
www.vishay.com
ESD PRECAUTION
Proper storage and handling procedures should be followed
to prevent ESD damage to the devices especially when they
are removed from the antistatic shielding bag. Electrostatic
sensitive devices warning labels are on the packaging.
TSOP753.., TSOP755..
Vishay Semiconductors
VISHAY SEMICONDUCTORS STANDARD
BAR CODE LABELS
The Vishay Semiconductors standard bar code labels are
printed at final packing areas. The labels are on each
packing unit and contain Vishay Semiconductors specific
data.
BAR CODE PRODUCT LABEL (example)
22178
Rev. 1.5, 22-Jul-16
11 Document Number: 82495
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
11 Page | ||
| Páginas | Total 12 Páginas | |
| PDF Descargar | [ Datasheet TSOP75536.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TSOP75530 | IR Receiver Modules | Vishay |
| TSOP75530W | IR Receiver Modules | Vishay |
| TSOP75533 | IR Receiver Modules | Vishay |
| TSOP75533W | IR Receiver Modules | Vishay |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |