|
|
PDF tm150xg-26l07 Data sheet ( Hoja de datos )
| Número de pieza | tm150xg-26l07 | |
| Descripción | LCD_Module | |
| Fabricantes | TIANMA | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de tm150xg-26l07 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
www.DataSheet4U.com
www.DataSheet4U.com
1 page  
[ Note 7 ] Measurement points
1/6Hp 1/2Hp 5/6Hp
1/6Vp
1
2
Active area
1/2Vp
3
5/6Vp
4
5
Vp: Total Number of Vertical pixel
Hp: Total Number of horizontal pixel
[ Note 8 ] Measurement condition
(1) Measurement equipment: BM-5A (TOPCON Corp.), Field=2°
(2) Ambient temperature Ta: 25 ± 2°C
(3) LCD: All pixels are WHITE, VDD=3.3V, fV=60Hz
(4) Measure after 30 minutes of CFL warm up.
(5) IL=TBDmArms
BACKLIGHT CHARACTERISTICS
This module is used the backlight with 2 CFL.
Please follow the characteristics of 1 CFL as below.
ITEM
Operating life
Lamp current
SYM. CONDITIOS MIN TYP MAX
tOL
(50000) -
-
IL (3) - (8)
UNIT
Hours
mArms
Ta=25°C
NOTE
at IL= TBD
(Recommended value)
Tottori SANYO Electric Co., Ltd. TM150XG-26L07 Ver.1 Page 4/13
5 Page 
(5) Water drop on LCD surface
Please do not leave LCD module with water drop. When the display surface gets
water drop, please wipe it off with cotton swab or soft cloth immediately, otherwise
display surface will be deteriorated.
If water gets in inside of LCD module, circuit may be damaged.
(6) Please make sure that LCD module is not warped or twisted at installation into
system. Even temporary warp or twist may be the cause for failure.
(7) Mechanical stress
Please be careful not to apply strong mechanical stress like drop or shock to LCD
module. Such stress may cause break of display glass and CFL or may be the
cause for failure.
(8) Pressure to display surface
Please be careful not to apply strong pressure to display surface. Such pressure
may cause scratches at surface or may be the cause of failure.
(9) Protection against scratch
Please be careful not to hit, press or rub the display surface with hard material like
tools. In addition, please do not put heavy or hard material on display surface, and
do not stack LCD modules. Polarizer at front surface can be easily scratched.
(10) Plugging in of connector
Please be careful not to apply strong stress to connector part of LCD module at
plugging in or out, because strong stress may damage the inside connection. At
plugging in connector, place LCD module on the flat surface and hold the backside
of connector on LCD module. Please make sure that connector is plugged in
correctly. Insecure connection may be the cause for failure during operation.
In addition, please be careful not to put the connecting cable between cabinet of
system and LCD module at installing LCD module into system.
(11) Handling of CFL cable and FPC (Flexible Printed Circuit)
Please be careful not to pull or scratch CFL cable, because CFL or soldered part of
cable may be damaged consequently.
Also FPC should not be pulled or scratched.
(12) Switching off before plugging in connector
Please make sure that power is switched off before plugging in connector.
If power is on at plugging in or out, circuit of LCD module may be damaged.
When LCD is switched on for test or inspection, please make sure that power
supply and input signals of driving system meet the specified power sequence.
(13) Temperature dependence of LCD display
Response speed (optical response) of LCD display is dependent on temperature.
Under low temperature, response speed is slower.
Also brightness and chromaticity change slightly depending on temperature.
(14) Slow light-up of CFL under low temperature
Under low temperature, start-up of CFL gets difficult. (The time from switch-on to
stable lighting becomes longer.)
As characteristic of CFL, operation under low temperature makes the life time
shorter. To avoid this, it is recommended to operate under normal temperature
(15) Condensation
LCD module may get condensation on its display surface and inside in the
circumstance where temperature changes much in short time.
Condensation can cause deterioration or failure. Therefore, please be careful not
to get condensation.
Tottori SANYO Electric Co., Ltd. TM150XG-26L07 Ver.1 Page 10/13
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet tm150xg-26l07.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| tm150xg-26l06 | LCD Module | TIANMA |
| tm150xg-26l07 | LCD_Module | TIANMA |
| TM150XG-26L09 | TFT COLOR LCD MODULE |  TORISAN |
| TM150XG-26L09A | TFT COLOR LCD MODULE | TORISAN |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |