|
|
PDF SF1186B-4 Data sheet ( Hoja de datos )
| Número de pieza | SF1186B-4 | |
| Descripción | SAW Filter | |
| Fabricantes | RF Monolithics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SF1186B-4 (archivo pdf) en la parte inferior de esta página. Total 4 Páginas | ||
|
No Preview Available !
• RF Filter for GPS Receiver
• Surface-mount 3.0 x 3.0 mm Package
• Complies with Directive 2002/95/EC (RoHS)
Absolute Maximum Ratings
Rating
Input Power Level
DC Voltage on any Non-ground Terminal
Operating Temperature Range
Storage Temperature Range in Tape and Reel
Maximum Soldering Profile, 5 cycles/ 10 seconds maximum
Pb
Value
10
3
-40 to +85
-40 to +85
265
Units
dBm
V
°C
°C
°C
SF1186B-4
1575 MHz
SAW Filter
Electrical Characteristics
Characteristic
Center Frequency
Insertion Loss, 1565 - 1585 MHz
Amplitude Ripple, 1565 - 1585 MHz
Attenuation, 0 dB Reference:
0 to 1000 MHz
1000 to 1435 MHz
1435 to 1525 MHz
1525 to 1540 MHz
1610 to 1625 MHz
1625 to 1715 MHz
1715 to 1785 MHz
1785 to 2100 MHz
2100 to 2200 MHz
2200 to 2500 MHz
2500 to 4000 MHz
Source Impedance, Unbalanced
Load Impedance, Balanced
Case Style
Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator
Standard Reel Quantity
Reel Size 7 Inch
Reel Size 13 Inch
Sym
fC
IL
Notes
Min
Typ
1575
2.7
0.4
SM3030-8
Max
4.5
1.5
Units
MHz
dB
dB
www.DataSheet.net/
ZS
ZL
32 34
32 34.5
22 24
7 21
7 16
22 25.5
34 39
30 34
25 26.5
27 34
18 32
50
50
SM3030-8 3.0 x 3.0 mm Nominal Footprint
905, YWWS
500 Pieces/Reel
3000 Pieces/Reel
dB
Ω
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50 Ω and measured with 50 Ω network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
www.RFM.com E-mail: [email protected]
©2009-2010 by RF Monolithics, Inc.
Page 1 of 4
SF1186B-4 7/21/10
Datasheet pdf - http://www.DataSheet4U.co.kr/
1 page | ||
| Páginas | Total 4 Páginas | |
| PDF Descargar | [ Datasheet SF1186B-4.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SF1186B-2 | SAW Filter | RF Monolithics |
| SF1186B-3 | SAW Filter | RF Monolithics |
| SF1186B-4 | SAW Filter | RF Monolithics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |