|
|
PDF SP4422A Data sheet ( Hoja de datos )
| Número de pieza | SP4422A | |
| Descripción | Electroluminescent Lamp Driver | |
| Fabricantes | Sipex | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SP4422A (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
|
No Preview Available !
®
SP4422A
Electroluminescent Lamp Driver
s 2.2V-5.0V Battery Operation
s 50nA Typical Standby Current
s High Voltage Output 160 VPP typical
s Internal Oscillator
APPLICATIONS
s PDAs
s Cellular Phones
s Remote Controls
s Handheld Computers
DESCRIPTION
The SP4422A is a high voltage output DC-AC converter that can operate from a 2.2V-5.0V
power supply. The SP4422A is capable of supplying up to 220 V signals, making it ideal
PP
for driving electroluminescent lamps. The device features 50 nA (typical) standby current, for
use in low power portable products. One external inductor is required to generate the high
voltage, and one external capacitor is used to select the oscillator frequency. The SP4422A
is offered in an 8-pin narrow and 8-pin micro SOIC packages. For delivery in die form, please
consult the factory.
HON 1
VSS 2
COIL 3
EL2 4
SP4422
8 CAP 2
7 CAP 1
6 VDD
5 EL1
SP4422A Block Diagram
SP4422ADS/15
SP4422A Electroluminescent Lamp Driver
1
© Copyright 2000 Sipex Corporation
1 page  
When the energy from the coil is released, a high
voltage spike is created triggering the SCR
switches. The direction of current flow is
determined by which SCR is enabled. One full
cycle of the H-bridge will create 16 voltage steps
from ground to 80V (typical) on pins 4 and 5 which
are 180 degrees out of phase from each other (see
figure 3 on page 9. A differential representation of
the outputs is shown in figure 4 on page 9.
Layout Considerations
The SP4422A circuit board layout must observe
careful analog precautions. For applications with
noisy voltage power supplies a 0.1µF low ESR
decoupling capacitor must be connected from VDD
to ground. Any high voltage traces should be
isolated from any digital clock traces or enable
lines. A solid ground plane connection is strongly
recommended. All traces to the coil or to the high
voltage outputs should be kept as short as possible
to minimize capacitive coupling to digital clock
lines and to reduce EMI emissions.
Electroluminescent Technology
What is electroluminescence?
An EL lamp is basically a strip of plastic that is
coated with a phosphorous material which emits
light (fluoresces) when a high voltage (>40V)
which was first applied across it, is removed or
reversed. Long periods of DC voltages applied to
the material tend to breakdown the material and
reduce its lifetime. With these considerations in
mind, the ideal signal to drive an EL lamp is a high
voltage sine wave. Traditional approaches to
achieving this type of waveform included discrete
circuits incorporating a transformer, transistors,
and several resistors and capacitors. This approach
is large and bulky, and cannot be implemented in
most hand held equipment. Sipex now offers low
power single chip driver circuits specifically
designed to drive small to medium sized
electroluminescent panels. All that is required is
one external inductor and capacitor.
Electroluminescent backlighting is ideal when used
with LCD displays, keypads, or other backlit
readouts. Its main use is to illuminate displays in
dim to dark conditions for momentary periods of
time. EL lamps typically consume less than LEDs
or bulbs making them ideal for battery powered
products. Also, EL lamps are able to evenly light
an area without creating "hot spots" in the display.
The amount of light emitted is a function of the
voltage applied to the lamp, the frequency at which
it is applied, the lamp material used and its size,
and lastly, the inductor used. There are many
variables which can be optimized for specific
applications. Sipex supplies characterization charts
to aid the designer in selecting the optimum circuit
configuration (see page 6).
HON=VDD=ON
HON=0V=OFF
VIN=3V +
–
NOTE:
Keep coil as close to the
SP4422A as possible
HON
VSS
Coil
COSC=100pF
Cap2
Cap1
VDD
0.1µF Low ESR
Decoupling
Capacitor
EL2 EL1
100Ω
SP4422A
17nF
NOTE:
Keep high voltage traces
short and away from VDD
and clock lines
SP4422A Test Circuit
SP4422ADS/15
SP4422A Electroluminescent Lamp Driver
5
© Copyright 2000 Sipex Corporation
5 Page 
EL polarizers/transflector
manufacturers
Nitto Denko
San Jose, CA
Phone: (510) 445-5400
Astra Products
Baldwin, NJ
Phone: (516) 223-7500
Fax: (516) 868-2371
EL Lamp manufacturers
Metro Mark/Leading Edge
Minnetonka, MN
Phone: (800) 680-5556
Phone: (612) 912-1700
Midori Mark Ltd.
1-5 Komagata 2-Chome
Taita-Ku 111-0043 Japan
Phone: 81-03-3848-2011
Luminescent Systems Inc. (LSI)
Lebanon, NH
Phone: (603) 643-7766
Fax: (603) 643-5947
NEC Corporation
Tokyo, Japan
Phone: (03) 3798-9572
Fax: (03) 3798-6134
Seiko Precision
Tokyo, Japan
Phone: (03) 5610-7089
Fax: .) 5610-7177
Gunze Electronics
2113 Wells Branch Parkway
Austin, TX 78728
Phone: (512) 752-1299
Fax: (512) 252-1181
SP4422ADS/15
SP4422A Electroluminescent Lamp Driver
11
© Copyright 2000 Sipex Corporation
11 Page | ||
| Páginas | Total 13 Páginas | |
| PDF Descargar | [ Datasheet SP4422A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SP4422A | Electroluminescent Lamp Driver | Sipex |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |