|
|
PDF MC14468 Data sheet ( Hoja de datos )
| Número de pieza | MC14468 | |
| Descripción | LONIZATION SMOKE DETECTOR IC WITH INTERCONNECT | |
| Fabricantes | Motorola Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MC14468 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
MOTOROLA
Freescale Semiconductor, Inc.
SEMICONDUCTOR TECHNICAL DATA
Order this document
by MC14468/D
MC14468
Low–Power CMOS
Ionization Smoke Detector IC
with Interconnect
The MC14468, when used with an ionization chamber and a small number of
external components, will detect smoke. When smoke is sensed, an alarm is sounded
via an external piezoelectric transducer and internal drivers. This circuit is designed to
operate in smoke detector systems that comply with UL217 and UL268 specifications.
• Ionization Type with On–Chip FET Input Comparator
• Piezoelectric Horn Driver
• Guard Outputs on Both Sides of Detect Input
• Input–Production Diodes on the Detect Input
• Low–Battery Trip Point, Internally Set, can be Altered Via External Resistor
• Detect Threshold, Internally Set, can be Altered Via External Resistor
• Pulse Testing for Low Battery Uses LED for Battery Loading
• Comparator Output for Detect
• Internal Reverse Battery Protection
• Strobe Output for External Trim Resistors
• I/O Pin Allows Up to 40 Units to be Connected for Common Signaling
• Power–On Reset Prevents False Alarms on Battery Change
16
1
P SUFFIX
PLASTIC DIP
CASE 648–08
ORDERING INFORMATION
MC14468P PLASTIC DIP
PIN ASSIGNMENT
(16 PIN DIP)
Detect
Comp. Out
I/O
Low V Set
Strobe
Out
LED
VDD
Timing
Resistor
Feedback
1
2
3
4
5
6
7
8
16 Guard Hi–Z
15 Detect Input
14 Guard Lo–Z
13 Sensitivity Set
12 Osc Capacitor
11 Silver
10 Brass
9 VSS
MAXIMUM RATINGS* (Voltages referenced to VSS)
Rating
DC Supply Voltage
Input Voltage, All Inputs Except Pin 8
DC Current Drain per Input Pin, Except Pin 15 = 1 mA
Symbol
VDD
Vin
I
Value
*0.5 to + 15
*0.25 to VDD + 0.25
10
Unit
V
V
mA
DC Current Drain per Output Pin
Operating Temperature Range
Storage Temperature Range
I 30 mA
*TA 10 to + 60
*Tstg 55 to + 125
°C
°C
Reverse Battery Time
tRB 5.0
s
* Maximum Ratings are those values beyond which damage to the device may occur.
This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields; however, it is advised that normal
v vprecautions be taken to avoid application of any voltage higher than maximum rated voltages to this high impedance circuit. For proper operation
it is recommended that Vin and Vout be constrained to the range VSS (Vin or Vout) VDD.
REV 3
© MMotootroolrao, lIanc.S2e0n00sor Device Data
For More Information On This Product,
Go to: www.freescale.com
1
1 page  
Freescale Semiconductor, Inc.
DEVICE OPERATION
MC14468
TIMING
The internal oscillator of the MC14468 operates with a
period of 1.67 seconds during no–smoke conditions. Each
1.67 seconds, internal power is applied to the entire IC and a
check is made for smoke, except during LED pulse, Low Bat-
tery Alarm Chirp, or Horn Modulation (in smoke). Every 24
clock cycles a check is made for low battery by comparing
VDD to an internal zener voltage. Since very small currents
are used in the oscillator, the oscillator capacitor should be of
a low leakage type.
DETECT CIRCUITRY
If smoke is detected, the oscillator period becomes 40 ms
and the piezoelectric horn oscillator circuit is enabled. The
horn output is modulated 160 ms on, 80 ms off. During the off
time, smoke is again checked and will inhibit further horn out-
put if no smoke is sensed. During local smoke conditions the
low battery alarm is inhibited, but the LED pulses at a 1.0 Hz
rate. In remote smoke, the LED is inhibited as well.
An active guard is provided on both pins adjacent to the
detect input. The voltage at these pins will be within 100 mV
of the input signal. This will keep surface leakage currents to
a minimum and provide a method of measuring the input volt-
age without loading the ionization chamber. The active guard
op amp is not power strobed and thus gives constant protec-
tion from surface leakage currents. Pin 15 (the Detect input)
has internal diode protection against static damage.
INTERCONNECT
The I/O (Pin 2), in combination with VSS, is used to inter-
connect up to 40 remote units for common signaling. A Local
Smoke condition activates a current limited output driver,
thereby signaling Remote Smoke to interconnected units. A
small current sink improves noise immunity during non–
smoke conditions. Remote units at lower voltages do not
draw excessive current from a sending unit at a higher volt-
age. The I/O is disabled for three oscillator cycles after power
up, to eliminate false alarming of remote units when the bat-
tery is changed.
SENSITIVITY/LOW BATTERY THRESHOLDS
Both the sensitivity threshold and the low battery voltage
levels are set internally by a common voltage divider (please
see Figure 1) connected between VDD and VSS. These volt-
ages can be altered by external resistors connected from
pins 3 or 13 to either VDD or VSS. There will be a slight inter-
action here due to the common voltage divider network. The
sensitivity threshold can also be set by adjusting the smoke
chamber ionization source.
TEST MODE
Since the internal op amps and comparators are power
strobed, adjustments for sensitivity or low battery level could
be difficult and/or time–consuming. By forcing Pin 12 to VSS,
the power strobing is bypassed and the output, Pin 1,
constantly shows smoke/no smoke. Pin 1 = VDD for smoke.
In this mode and during the 10 ms power strobe, chip current
rises to approximately 50 µA.
LED PULSE
The 9–volt battery level is checked every 40 seconds dur-
ing the LED pulse. The battery is loaded via a 10 mA pulse
for 10 ms. If the LED is not used, it should be replaced with
an equivalent resistor such that the battery loading remains
at 10 mA.
HYSTERESIS
When smoke is detected, the resistor/divider network that
sets sensitivity is altered to increase sensitivity. This yields
approximately 100 mV of hysteresis and reduces false
triggering.
TO
OTHER
UNITS
0.1 µF
330 Ω
+ 8.2 MΩ
9V
1 16
MC14468
2 15
3 14
4 13
5 12
6 11
7 10
89
1M 1M
TEST
0.1 µF
*NOTE: Component values may change
depending on type of piezoelectric horn used.
1.5 MΩ*
0.001 µF
220 kΩ*
Figure 5. Typical Application as Ionization Smoke Detector
Motorola Sensor Device Data For More Information On This Product,
Go to: www.freescale.com
5
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet MC14468.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MC14467-1 | Low-Power CMOS Ionization Smoke Detector IC |  Freescale Semiconductor |
| MC14467P1 | IONIZATION SMOKE DETECTOR | Motorola Semiconductors |
| MC14467P1 | Other Analog Circuits | Motorola Semiconductors |
| MC14468 | LONIZATION SMOKE DETECTOR IC WITH INTERCONNECT | Motorola Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |