|
|
PDF MAX8630Y Data sheet ( Hoja de datos )
| Número de pieza | MAX8630Y | |
| Descripción | Charge Pumps | |
| Fabricantes | Maxim Integrated Products | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MAX8630Y (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
19-3689; Rev 1; 2/07
EVAALVUAAILTAIOBNLEKIT
125mA 1x/1.5x Charge Pumps for
5 White LEDs in 3mm x 3mm TDFN
General Description
The MAX8630Y/MAX8630Z charge pumps drive up to 5
white LEDs with regulated constant current up to 125mA
total. By utilizing adaptive 1x/1.5x charge-pump modes
and very low-dropout current regulators, they achieve
high efficiency over the full 1-cell Li+ battery input volt-
age range. The 1MHz fixed-frequency switching allows
for tiny external components, and the regulation scheme
is optimized to ensure low EMI and low input ripple. An
integrated derating function protects the LEDs from
overheating during high ambient temperatures.
The MAX8630Y/MAX8630Z are factory trimmed for full-
scale LED current options of 15mA, 18mA, 20mA, and
25mA. The MAX8630Z uses two enable inputs (ENM for
3 main LEDs and ENS for 2 sub LEDs) for simple on/off
control and single-wire, serial-pulse dimming in 32 linear
steps. The MAX8630Y uses a single direct PWM input
(PWM) to control all 5 LEDs with DC current proportional
to the PWM duty cycle. If both ENM and ENS (or PWM)
are kept low for more than 4ms, the MAX8630_ enters
shutdown. The MAX8630Y/MAX8630Z are available in a
14-pin, 3mm x 3mm TDFN package (0.8mm max height).
Applications
Display Backlight (Up to 5 LEDs)
Main (3 LEDs) + Sub (2 LEDs) Displays
Cell Phones and Smartphones
PDAs, Digital Cameras, and Camcorders
Typical Operating Circuit
Features
♦ 93% Max/85% Avg. Efficiency (PLED/PBATT) Over
Li+ Battery Discharge
♦ 1% LED Current Accuracy
♦ 125mA Total Drive Capability
♦ Adaptive 1x/1.5x Mode Switchover
♦ Single-Wire, Serial-Pulse Dimming (MAX8630Z)
Independent On/Off/Dimming for Main and Sub
Linear—Full, 31/32nd, 30/32nd, … 1/32nd
♦ Direct-PWM Dimming (MAX8630Y)
♦ 15, 18, 20, and 25mA Full-Scale Versions
♦ Low 0.1µA Shutdown Current
♦ Soft-Start Eliminates Inrush Current
♦ Output Overvoltage Protection
♦ Thermal-Derating Function Protects LEDs
♦ 14-Pin, 3mm x 3mm TDFN Package
Ordering Information
PART
PIN-
PACKAGE
TOP
MARK
PKG
CODE
MAX8630YETD15+T
14 TDFN
(3mm x 3mm)
AAS
T1433-2
Note: All devices are specified to operate over the -40°C to
+85°C operating temperature range.
+Denotes a lead-free package.
Ordering Information continued at end of data sheet.
Selector Guide appears at end of data sheet.
Pin Configuration
INPUT
2.7V TO 5.5V
1μF
ENABLE MAIN
ON/OFF AND
DIMMING
ENABLE SUB
ON/OFF AND
DIMMING
1μF
C1P C1N
IN OUT
GND MAX8630Z
LED1
LED2
ENM LED3
LED4
ENS LED5
C2P C2N
OUTPUT
1μF
MAIN
SUB
TOP VIEW
14 13 12 11 10 9 8
MAX8630Y
MAX8630Z
1234567
1μF
TDFN
3mm × 3mm
( ) ARE FOR MAX8630Y
________________________________________________________________ Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1 page  
www.DataSheet4U.com
125mA 1x/1.5x Charge Pumps for 5 White LEDs
in 3mm x 3mm TDFN
Typical Operating Characteristics (continued)
(VIN = 3.6V, ENM = ENS = IN, TA = +25°C, unless otherwise noted.)
VENM AND
VENS
VOUT
IIN
IOUT
STARTUP AND SHUTDOWN
MAX8630Y/Z toc11
5V/div
2V/div
1ms/div
0
100mA/div
0
100mA/div
0
VENM AND
VENS
VOUT
STARTUP AND DIMMING
MAX8630Y/Z toc13
5V/div
1V/div
VENM
VOUT
IIN
MAIN STARTUP AND SHUTDOWN
WITH SUB ENABLED
MAX8630Y/Z toc12
5V/div
2V/div
0
100mA/div
0
IOUT 100mA/div
0
1ms/div
LINE-TRANSIENT RESPONSE WITH MODE CHANGE
(VIN = 3.8V TO 3.2V TO 3.8V)
MAX8630Y/Z toc14
VIN 1V/div
VOUT 500mV/div
3V
50mA/div
IOUT
20mA/div
IOUT
0
20ms/div
200μs/div
Pin Description
PIN
MAX8630Z
MAX8630Y
11
22
33
44
NAME
FUNCTION
GND
C1N
IN
C2N
Ground. Connect GND to system ground and the input bypass capacitor as
close to the IC as possible. Connect GND to the exposed pad directly under
the IC.
Transfer Capacitor 1 Negative Connection. Connect a 1µF ceramic capacitor
from C1P to C1N.
Supply Voltage Input. Connect a 1µF ceramic capacitor from IN to GND. The
input voltage range is 2.7V to 5.5V.
Transfer Capacitor 2 Negative Connection. Connect a 1µF ceramic capacitor
from C2P to C2N.
_______________________________________________________________________________________ 5
5 Page 
www.DataSheet4U.com
125mA 1x/1.5x Charge Pumps for 5 White LEDs
in 3mm x 3mm TDFN
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
______________________________________________________________________________________ 11
11 Page | ||
| Páginas | Total 12 Páginas | |
| PDF Descargar | [ Datasheet MAX8630Y.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MAX8630W | Triple-Channel Video Reconstruction Filter and Buffer | Maxim Integrated Products |
| MAX8630X | Triple-Channel Video Reconstruction Filter and Buffer | Maxim Integrated Products |
| MAX8630Y | Charge Pumps | Maxim Integrated Products |
| MAX8630Z | Charge Pumps | Maxim Integrated Products |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |