|
|
PDF AX5202 Data sheet ( Hoja de datos )
| Número de pieza | AX5202 | |
| Descripción | Step-up PWM DC/DC Converter | |
| Fabricantes | AXElite | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AX5202 (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
|
No Preview Available !
AX5202
Step-up PWM DC/DC Converter
GENERAL DESCRIPTION
The AX5202 is high efficient step-up DC/DC converter. Large output current is
possible having a built in internal N channel MOSFET, and using an external coil and
diode.
The AX5202 can be operated at switching frequencies of 500 kHz allowing for easy
filtering and low noise, the size of the external components can be reduced.
Output voltage is programmable with 1.0V of standard voltage supply internal, and
using externally connected components, output voltage (FB) can be set up at will. The
soft-start time can be programmed by outside capacitor; the function prevents overshoot at
startup. Build inside Current limit, Thermal Shutdown and enable functions.
FEATURES
- Input voltage：3V to 16V
- Output voltage：3.3V to 23V
- Duty ratio：0% to 85% PWM control
- Oscillation frequency：500KHz.
- Enable and Thermal Shutdown function.
- Internal Current limit.
- Built-in N-channel MOSFET
- SOP-8L with Exposed pad Pb-Free package.
BLOCK DIAGRAM
VCC
FB
Phase
Compensation
Regulator
+
-
Vref=1.0V
PWM
Controller
EN
VEN
8uA
Thermal
Shutdown
+
-
Oscillator
Buffer
Driver
0.06V
SW
SS
SGND
PGND
1/10
Axelite Confidential Materials, do not copy or distribute without written consent.
Rev.1.2 Jan.25, 2011
1 page  
AX5202
V 1.0V 1 R4
OUT R3
Table 1 Resistor select for output voltage setting
VOUT
R3
R4
12V 1K 11K
15V 1.3K 18K
18V 1.3K 22K
Inductor Selection
For most designs, Low inductance values are physically smaller but require faster
switching, which results in some efficiency loss. The inductor value can be derived from the
following equation:
V V V
IN
OUT
IN
L V I f
OUT
L LX
Where is inductor Ripple Current. Large value inductors lower ripple current and
small value inductors result in high ripple currents. Choose inductor ripple current
approximately 15% of the maximum input current 1.6A, ΔIL=0.24A.
Table 2 Inductor select for output voltage setting (VCC=5V)
VOUT
9V
12V 15V 18V
L1
Value
18uH
22uH
25uH
33uH
The DC current rating of the inductor should be at least equal to the maximum load
current plus half the ripple current to prevent core saturation (1.6A+0.12A).
Input Capacitor Selection
The input capacitor reduces the surge current drawn from the input and switching
noise from the device. The input capacitor impedance at the switching frequency shall be
less than input source impedance to prevent high frequency switching current passing to
the input. A low ESR input capacitor sized for maximum RMS current must be used.
The capacitor voltage rating should be at least 1.5 times greater than the input
voltage, and often much higher voltage ratings are needed to satisfy.
5/10
Axelite Confidential Materials, do not copy or distribute without written consent.
Rev.1.2 Jan.25, 2011
5 Page | ||
| Páginas | Total 10 Páginas | |
| PDF Descargar | [ Datasheet AX5202.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AX5201 | Step-up PWM DC/DC Converter |  Axelite |
| AX5201 | Boost Drive Solution |  GOFO tech |
| AX5202 | Step-up PWM DC/DC Converter | AXElite |
| AX5203 | Step-up PWM DC/DC Converter | AXElite |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |