|
|
PDF STCF01 Data sheet ( Hoja de datos )
| Número de pieza | STCF01 | |
| Descripción | Step-up converter | |
| Fabricantes | STMicroelectronics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de STCF01 (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
|
No Preview Available !
STCF01
Step-up converter for cell phone camera flash LEDs
General features
■ Supply voltage range: 2.6V to 5.5V
■ 17V Maximum output voltage
■ Two current levels up to 300mA set with
external resistors
■ Dedicated pin to select the required level of
current
■ Operating frequency: 1.5MHz: PWM Controller
■ Torch mode supported
■ Shutdown pin with true load disconnection
■ Efficiency: 90% at 100mA; 80% at 300mA
■ DFN10L (3mm x 3mm) Package
Description
The STCF01 is a dedicated IC designed to drive
two, three, or four white, cell phone camera flash
LEDs with constant current. The step-up (boost)
converter input is connected directly to the battery,
and its converter output voltage is automatically
determined using current feedback-based duty
cycle control.
The STCF01 has a dedicated pin for two levels of
www.DataSLhEeDet4cUu.crroemnt selection. An external resistor is used
DFN10L (3x3)
to set the required current for each level.
Compared to the linear current control technique,
this method allows designers to achieve the best
and most efficient performance possible with the
selected current, thereby avoiding linear element
losses.
The Shutdown (SHDN) pin saves power when the
camera flash is not used by consuming less than
0.1µA of current. When the SHDN pin is high
(logic '1'), the device is turned OFF and there is no
DC current path from the supply to the white LEDs
(Load Disconnect). If it is held to GND, the output
current continuously flows through the LEDs
(Torch mode). The SHDN pin, when it is set to low
(logic '0'), is also used to set the flash function
time duration.
Order code
Part number
STCF01PMR
October 2006
Package
DFN10L (3mm x 3mm)
Rev. 4
Packaging
4500 parts per reel
1/16
www.st.com
16
1 page  
STCF01
3 Application information
Figure 3. Application circuit
Application information
www.DataSheet4U.com
5/16
5 Page 
STCF01
Typical operating characteristics
.
Figure 16. Maximum duty cycle vs temperature Figure 17. Turn on and off response
Figure 18. Turn on time
VSHDN=pulse, FREQ.=1Hz, Tr=Tf=10µs
Figure 19. Start up transient
VSHDN=pulse, FREQ.=1Hz, Tr=Tf=10µs
www.DataSheet4U.com
Figure 20. Multi shoot mode
VI=0 to 3.6V, VSEL=GND, VSHDN=GND
Figure 21. Torch mode behavior
VSEL=GND, VSHDN=pulse
VSEL=GND, VSHDN=GND
11/16
11 Page | ||
| Páginas | Total 16 Páginas | |
| PDF Descargar | [ Datasheet STCF01.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| STCF01 | Step-up converter | STMicroelectronics |
| STCF02 | High power white led driver | STMicroelectronics |
| STCF03 | High power white LED driver | STMicroelectronics |
| STCF04 | High power white LED SuperCap driver | STMicroelectronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |