|
|
Número de pieza | SSMB | |
Descripción | (SSMB / SSMC) RF Coaxial Connectors | |
Fabricantes | ITT Industries | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de SSMB (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! RF Coaxial Connectors
Introduction
This range of 50 ohm microminiature radio
frequency connectors is suitable for both military
and commercial equipment operating at
frequencies up to 4 GHz (SSMB) and 12.4 GHz
(SSMC). They provide a choice of Snap-on
(SSMB) or Screw-on (SSMC) and are available for
a wide range of flexible cables.
SSMC connectors are used where a positive
mechanical engagement is required and where
space permits the use of torque wrenches. SSMB
connectors are quick disconnect versions of the
SSMC and are used in applications where limited
space prohibits the use of torque wrenches or
when components or modules must be quickly
changed to keep down time to a minimum.
Mating Interfaces
SSMB (Snap-on)
www.DataSheet4U.com
SSMC (Screw-on)
PLUG
SSMB/SSMC
SSMB/C
JACK
PLUG JACK
NOTES
1) Inside diameter of female contact to meet VSWR when mated with a 0,36 - 0,38 (.014 - .015) 2) Must meet the force to engage and disengage
mating characteristics and connector durability diameter male contact.
when mated with its mating part.
Dimensions are shown in mm (inch)
Dimensions subject to change
31
1 page RF Coaxial Connectors
Recommended Mounting Hole Dimensions
Mounting Information
Plan R
Plan Thread Size
U 6-40 UNF-2A
V 10-32 UNF-2A
W 1/4-36 UNS-2A
X 5/16-32 UNEF-2A
Y 7/16-28 UNEF-2A
Z 1/2-28 UNEF-2A
AA 5/8-24 UNEF-2A
Plan S
A
+0,13
−0,00
(.005)
(.000)
3,56 (.140)
4,95 (.195)
6,73 (.265)
7,94 (.313)
11,91 (.469)
13,08 (.515)
16,26 (.640)
B
+0,13
−0,00
(.005)
(.000)
3,20 (.126)
4,50 (.177)
5,92 (.233)
7,40 (.291)
10,41 (.410)
12,19 (.480)
15,24 (.600)
Plan
Thread Size
A
+0,10
−0,03
(.004)
(.001)
B
+0,10
−0,03
(.004)
(.001)
BB
M9
9,20 (.362)
8,20 (.322)
CC
M5
5,90 (.232)
5,00 (.197)
Plan T
Plan U - AA
Plan BB-CC
Mounting
Plan DD
Plan EE
Plan FF
Dimensions are shown in mm (inch)
Dimensions subject to change 109
5 Page RF Coaxial Connectors
Assembly Instructions
AI-129, AI-286 & AI-696 SSMB/SSMC Right Angle Connectors, Crimp Type for Braided Cable
HEAT
SHRINKABLE
TUBING
CRIMP
FERRULE
INSERT OR CAP
REAR BODY
1. Slide heat shrinkable tubing and ferrule on to cable.
2. Trim cable to dimensions shown.
Assembly Instruction No.
AI-129
AI-286
AI-696
A
5,56 (.219)
6,35 (.250)
6,22 (.245)
B
2,77 (.109)
2,77 (.109)
2,54 (.100)
C
1,19 (.047)
0,79 (.031)
1,14 (.045)
3. Tin center conductor (DO NOT OVER TIN).
4. Slide body over cable dielectric and under the braid until braid is flush against under-side of rear
body. Ensure center conductor is located in the forked end of the contact.
NOTE. When using cables with inflexible jackets it is permissible to make two 3,00 (.118)
longitudinal slits in the outer jacket.
5. Slide ferrule flush against the body and crimp in position using ITT Cannon Crimp Tool and suitable
die set (see table).
6. Using a small soldering iron solder center conduct to contact.
NOTE: The center conductor should not protrude beyond the contact or touch the body. Solder
should not protrude beyond the slotted section of the contact.
Assy Insts
7. Press insert into place or locate the cap in rear of body and dimple or lightly punch to ensure it is
locked in position (recommended tool, flat pin X3,07 ± 0,05 (.121 ± .002).
8. Slide heat shrinkable tubing over ferrule flush against body and heat until tubing shrinks down.
Only common cable retention features are shown in detail. Various body configurations can apply.
Cable Type
RG196/U
RG316/U
RD316
Cable Code
3196
3188
3875
Die Size
2,67 (.105)
3,25 (.128)
3,84 (.151)
Dimensions are shown in mm (inch)
Dimensions subject to change 115
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet SSMB.PDF ] |
Número de pieza | Descripción | Fabricantes |
SSM-2005 | SSM2005 | Analog Devices |
SSM-2005 | Decoder 5.1-Channel Soundfield Generator | Analog Devices |
SSM-2014 | OPERATIONAL VOLTAGE CONTROLLED ELEMENT | ETC |
SSM-2015 | Microphone Preamplifier | PMI |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |