DataSheet.es    


PDF SST13LP01 Data sheet ( Hoja de datos )

Número de pieza SST13LP01
Descripción Dual-Band Power Amplifier
Fabricantes SST　
Logotipo SST Logotipo



Hay una vista previa y un enlace de descarga de SST13LP01 (archivo pdf) en la parte inferior de esta página.


Total 27 Páginas

No Preview Available ! SST13LP01 Hoja de datos, Descripción, Manual

www.DataSheet4U.com
2.4-2.5 GHz / 4.9-5.8 GHz Dual-Band Power Amplifier
SST13LP01
FEATURES:
SST13LP012.4 GHz / 5 GHz Dual-Band Power Amplifier
Preliminary Specifications
• High Gain:
– Typically 28 dB gain across 2.4-2.5 GHz over
temperature 0°C to +85°C
– Typically 30-33 dB gain across 4.9-5.8 GHz over
temperature 0°C to +85°C
• High linear output power:
– >29 dBm P1dB across 2.4-2.5 GHz
(Exceeding maximum rating of average output
power, never measure with CW source! Pulsed
single-tone source with <50% duty cycle is rec-
ommended.)
– Meets 802.11g OFDM ACPR requirement up to
23 dBm
– Added EVM~4% up to 21 dBm for
54 Mbps 802.11g signal
– Meets 802.11b ACPR requirement up to 23 dBm
– ~28 dBm P1dB (Pulsed single-tone signal)
across 4.9~5.8 GHz
– Meets 802.11a OFDM ACPR requirement up to
22 dBm over whole band
– Added EVM~4% up to 20 dBm for
54 Mbps 802.11a signal
• High power-added efficiency/Low operating
current for both 802.11a/b/g applications
– ~24%/250 mA @ POUT = 23 dBm for 802.11g
– ~23%/260 mA @ POUT = 23 dBm for 802.11b
– ~9.5%/320 mA @ POUT = 20 dBm for 802.11a
• Built-in Ultra-low IREF power-up/down control
– IREF <3 mA
• Low idle current
– ~70 mA ICQ (802.11b/g)
– ~170 mA ICQ (802.11a)
• High-speed power-up/down
– Turn on/off time (10%~90%) <100 ns
– Typical power-up/down delay with driver delay
included <200 ns
• High temperature stability
– ~1 dB gain/power variation between 0°C to +85°C
across 2.4~2.5 GHz
– ~3.5/1.5 dB gain/max linear power variation
between 0°C to +85°C across 4.9~5.8 GHz
– ~1 dB detector variation over 0°C to +85°C
• Low shut-down current (< 0.1 µA)
• On-chip power detection
• 20 dB dynamic range on-chip power detection
• Simple input/output matching
• Packages available
– 24-contact WQFN (4mm x 4mm)
– Non-Pb (lead-free) packages available
APPLICATIONS:
• WLAN (IEEE 802.11a/g/b)
• Japanese WLAN
• HyperLAN2
• Multimedia
• Home RF
• Cordless phones
PRODUCT DESCRIPTION
The SST13LP01 is a high-gain, high-performance, dual-
band power amplifier IC based on the highly-reliable
InGaP/GaAs HBT technology.
The SST13LP01 device can be easily configured for high-
power applications with superb power-added efficiency
while operating over the 802.11a/b/g frequency band for
U.S., European, and Japanese markets (2.4-2.5 GHz and
4.9-5.8 GHz.
The SST13LP01 has excellent linearity, typically ~4%
added EVM at 21 dBm output power which is essential for
54 Mbps 802.11g operation while meeting 802.11g spec-
trum mask at 23 dBm and 802.11b spectrum mask at 23
dBm. For 802.11a operation, the SST13LP01 has demon-
strated typically ~4% added EVM at 20 dBm output power
while meeting 802.11a spectrum mask at 22 dBm. The
SST13LP01 also has wide-range (>20 dB), temperature-
stable (~1 dB over 85°C), single-ended/differential power
detectors which lower users’ cost on power control.
The power amplifier IC also features easy board-level
usage along with high-speed power-up/down control.
Ultra-low reference current (total IREF <3 mA) makes the
SST13LP01 controllable by an on/off switching signal
directly from the baseband chip. These features, coupled
with low operating current, make the SST13LP01 ideal
for the final stage power amplification in both battery-
powered 802.11a/b/g WLAN transmitter and access
point applications.
The SST13LP01 is offered in a 24-contact WQFN package.
See Figure 1 for pin assignments and Table 1 for pin
descriptions.
©2005 SST Communications Corp.
S71287-00-000
11/05
1
The SST logo and SuperFlash are registered Trademarks of Silicon Storage Technology, Inc.
These specifications are subject to change without notice.

1 page




SST13LP01 pdf
2.4-2.5 GHz / 4.9-5.8 GHz Dual-Band Power Amplifier
SST13LP01
ELECTRICAL SPECIFICATIONS
Preliminary Specifications
The AC and DC specifications for the power amplifier interface signals. Refer to Table 2 for the DC voltage and current spec-
ifications. Refer to Figures 2 through 28 for the RF performance.
Absolute Maximum Stress Ratings (Applied conditions greater than those listed under “Absolute Maximum Stress Rat-
ings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these
conditions or conditions greater than those defined in the operational sections of this data sheet is not implied. Exposure to
absolute maximum stress rating conditions may affect device reliability.)
Supply Voltage at pins 7, 9, 10, 11, 21, and 23 (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +4.0V
Reference Voltage at pins 6 and 22 (VREF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +3.3V
DC supply current (ICC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 mA
Operating Temperature (TA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40ºC to +85ºC
Storage Temperature (TSTG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40ºC to +120ºC
Maximum Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150ºC
Surface Mount Solder Reflow Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C for 10 seconds
OPERATING RANGE
Range
Industrial
Ambient Temp
-40°C to +85°C
VCC
3.3V
©2005 SST Communications Corp.
5
S71287-00-000
11/05

5 Page





SST13LP01 arduino
2.4-2.5 GHz / 4.9-5.8 GHz Dual-Band Power Amplifier
SST13LP01
Preliminary Specifications
TYPICAL PERFORMANCE CHARACTERISTICS
TEST CONDITIONS: VCC = 3.3V, VREG_LB = 2.85V, TA = 25°C, 1 MPBS 802.11B CCK SIGNAL
10
Freq = 2.412 GHz
0
Freq = 2.442 GHz
-10 Freq = 2.484 GHz
-20 POUT = 23 dBm
DC current 265 mA
-30
-40
-50
-60
-70
-80
2.35
2.40
2.45
Frequency (GHz)
2.50
2.55
FIGURE 7: LOW BAND 802.11B SPECTRUM MASK AT 23 DBM WITH DC CURRENT OF 265 MA
©2005 SST Communications Corp.
11
S71287-00-000
11/05

11 Page







PáginasTotal 27 Páginas
PDF Descargar[ Datasheet SST13LP01.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
SST13LP01Dual-Band Power AmplifierSST
SST
SST13LP02Dual-Band Power AmplifierSST
SST
SST13LP052.4-2.5 GHz / 4.9-5.8 GHz Dual-Band Power Amplifier ModuleSST
SST

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

 Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

 Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar