파트넘버.co.kr MMBTH81LT1 데이터시트 PDF


MMBTH81LT1 반도체 회로 부품 판매점

UHF/VHF Transistor



Motorola Semiconductors 로고
Motorola Semiconductors
MMBTH81LT1 데이터시트, 핀배열, 회로
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Order this document
by MMBTH81LT1/D
UHF/VHF Transistor
PNP Silicon
COLLECTOR
3
1
BASE
MMBTH81LT1
Motorola Preferred Device
MAXIMUM RATINGS
2
EMITTER
Rating
Symbol
Value
Unit
Collector–Emitter Voltage
Collector–Base Voltage
Emitter–Base Voltage
DEVICE MARKING
VCEO
VCBO
VEBO
–20
–20
–3.0
Vdc
Vdc
Vdc
MMBTH81LT1 = 3D
THERMAL CHARACTERISTICS
Characteristic
Total Device Dissipation FR-5 Board,(1)
TA = 25°C
Derate above 25°C
Symbol
PD
Thermal Resistance, Junction to Ambient
Total Device Dissipation
Alumina Substrate,(2) TA = 25°C
Derate above 25°C
RθJA
PD
Thermal Resistance, Junction to Ambient
RθJA
Junction and Storage Temperature
TJ, Tstg
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)
Characteristic
Symbol
Min
OFF CHARACTERISTICS
Collector–Emitter Breakdown Voltage (IC = –1.0 mAdc, IB = 0)
Collector–Base Breakdown Voltage (IC = –10 µAdc, IE = 0)
Emitter–Base Breakdown Voltage (IE = –10 µAdc, IC = 0)
Collector Cutoff Current (VCB = –10 Vdc, IE = 0)
Emitter Cutoff Current (VEB = –2.0 Vdc, IC = 0)
ON CHARACTERISTICS
V(BR)CEO
V(BR)CBO
V(BR)EBO
ICBO
IEBO
–20
–20
–3.0
DC Current Gain (IC = –5.0 mAdc, VCE = –10 Vdc)
Collector–Emitter Saturation Voltage (IC = –5.0 mAdc, IB = –0.5 mAdc)
Base–Emitter On Voltage (IC = –5.0 mAdc, VCE = –10 Vdc)
SMALL–SIGNAL CHARACTERISTICS
hFE
VCE(sat)
VBE(on)
60
Current–Gain – Bandwidth Product
(IC = –5.0 mAdc, VCE = –10 Vdc, f = 100 MHz)
fT 600
Collector–Base Capacitance (VCB = –10 Vdc, IE = 0, f = 1.0 MHz)
Collector–Emitter Capacitance (IB = 0, VCB = –10 Vdc, f = 1.0 MHz)
Ccb —
Cce —
1. FR–5 = 1.0 x 0.75 x 0.062 in.
2. Alumina = 0.4 x 0.3 x 0.024 in. 99.5% alumina.
Thermal Clad is a trademark of the Bergquist Company
Preferred devices are Motorola recommended choices for future use and best overall value.
3
1
2
CASE 318 – 08, STYLE 6
SOT– 23 (TO – 236AB)
Max
225
1.8
556
300
2.4
417
– 55 to +150
Unit
mW
mW/°C
°C/W
mW
mW/°C
°C/W
°C
Typ Max Unit
— — Vdc
— — Vdc
— — Vdc
–100
nAdc
–100
nAdc
———
— –0.5 Vdc
— –0.9 Vdc
— — MHz
— 0.85 pF
— 0.65 pF
©MMotootorroollaa,
Small–Signal
Inc. 1996
Transistors,
FETs
and
Diodes
Device
Data
1


MMBTH81LT1 데이터시트, 핀배열, 회로
MMBTH81LT1
INFORMATION FOR USING THE SOT–23 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
0.037
0.95
0.037
0.95
0.035
0.9
0.079
2.0
0.031
0.8
inches
mm
SOT–23
SOT–23 POWER DISSIPATION
The power dissipation of the SOT–23 is a function of the
pad size. This can vary from the minimum pad size for
soldering to a pad size given for maximum power dissipation.
Power dissipation for a surface mount device is determined
by TJ(max), the maximum rated junction temperature of the
die, RθJA, the thermal resistance from the device junction to
ambient, and the operating temperature, TA. Using the
values provided on the data sheet for the SOT–23 package,
PD can be calculated as follows:
PD =
TJ(max) – TA
RθJA
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
the equation for an ambient temperature TA of 25°C, one can
calculate the power dissipation of the device which in this
case is 225 milliwatts.
PD =
150°C – 25°C
556°C/W
= 225 milliwatts
The 556°C/W for the SOT–23 package assumes the use
of the recommended footprint on a glass epoxy printed circuit
board to achieve a power dissipation of 225 milliwatts. There
are other alternatives to achieving higher power dissipation
from the SOT–23 package. Another alternative would be to
use a ceramic substrate or an aluminum core board such as
Thermal Clad. Using a board material such as Thermal
Clad, an aluminum core board, the power dissipation can be
doubled using the same footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100°C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference shall be a maximum of 10°C.
The soldering temperature and time shall not exceed
260°C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient shall be 5°C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied during
cooling.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
2 Motorola Small–Signal Transistors, FETs and Diodes Device Data




PDF 파일 내의 페이지 : 총 4 페이지

제조업체: Motorola Semiconductors

( motorola )

MMBTH81LT1 transistor

데이터시트 다운로드
:

[ MMBTH81LT1.PDF ]

[ MMBTH81LT1 다른 제조사 검색 ]




국내 전력반도체 판매점


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877

[ 홈페이지 ]

IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈

( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )

전력반도체 문의 : 010-3582-2743



일반적인 전자부품 판매점


디바이스마트

IC114

엘레파츠

ICbanQ

Mouser Electronics

DigiKey Electronics

Element14


관련 데이터시트


MMBTH81LT1

UHF/VHF Transistor - Motorola Semiconductors