9410A 반도체 회로 부품 판매점
Single N-Channel Enhancement Mode Field Effect Transistor
|
|
 Fairchild Semiconductor |
93LC76/86
8K/16K 2.5V Microwire® Serial EEPROM
FEATURES
• Single supply with programming operation down
to 2.5V
• Low power CMOS technology
- 1 mA active current typical
- 5 µA standby current (typical) at 3.0V
• ORG pin selectable memory configuration
1024 x 8 or 512 x 16 bit organization (93LC76)
2048 x 8 or 1024 x 16 bit organization (93LC86)
• Self-timed ERASE and WRITE cycles
(including auto-erase)
• Automatic ERAL before WRAL
• Power on/off data protection circuitry
• Industry standard 3-wire serial I/O
• Device status signal during ERASE/WRITE cycles
• Sequential READ function
• 10,000,000 ERASE/WRITE cycles guaranteed
• Data retention > 200 years
• 8-pin PDIP/SOIC package
• Temperature ranges available
- Commercial (C)
- Industrial (I)
0°C to +70°C
-40°C to +85°C
DESCRIPTION
The Microchip Technology Inc. 93LC76/86 are 8K and
16K low voltage serial Electrically Erasable PROMs.
The device memory is configured as x8 or x16 bits
depending on the ORG pin setup. Advanced CMOS
technology makes these devices ideal for low power
non-volatile memory applications. These devices also
have a Program Enable (PE) pin to allow the user to
write protect the entire contents of the memory array.
The 93LC76/86 is available in standard 8-pin DIP and
8-pin surface mount SOIC packages.
PACKAGE TYPES
DIP Package
CS 1
CLK 2
DI 3
DO 4
8 VCC
7 PE
6 ORG
5 VSS
SOIC Package
CS 1
CLK 2
DI 3
DO 4
8 VCC
7 PE
6 ORG
5 VSS
BLOCK DIAGRAM
VCC VSS
Memory
Array
Address
Decoder
Data
Register
DI
Mode
PE
CS
Decode
Logic
CLK
Clock
Generator
Address
Counter
Output
Buffer
DO
Microwire is a registered trademark of National Semiconductor Incorporated.
© 1996 Microchip Technology Inc.
Preliminary
This document was created with FrameMaker 4 0 4
DS21131C-page 1
93LC76/86
1.0 ELECTRICAL
CHARACTERISTICS
1.1 Maximum Ratings*
VCC ...................................................................................7.0V
All inputs and outputs w.r.t. VSS ............... -0.6V to Vcc +1.0V
Storage temperature ..................................... -65˚C to +150˚C
Ambient temp. with power applied................. -65˚C to +125˚C
Soldering temperature of leads (10 seconds) ............. +300˚C
ESD protection on all pins................................................4 kV
*Notice: Stresses above those listed under “Maximum ratings”
may cause permanent damage to the device. This is a stress rat-
ing only and functional operation of the device at those or any
other conditions above those indicated in the operational listings
of this specification is not implied. Exposure to maximum rating
conditions for extended periods may affect device reliability
TABLE 1-1: PIN FUNCTION TABLE
1.2 AC Test Conditions
AC Waveform:
VLO = 2.0V
VHI = Vcc - 0.2V
VHI = 4.0V for
(Note 1)
(Note 2)
Timing Measurement Reference Level
Input
0.5 VCC
Output
0.5 VCC
Note 1: For VCC ≤ 4.0V
2: For VCC > 4.0V
Name
CS
CLK
DI
DO
VSS
ORG
PE
VCC
Function
Chip Select
Serial Data Clock
Serial Data Input
Serial Data Output
Ground
Memory Configuration
Program Enable
Power Supply
TABLE 1-2: DC CHARACTERISTICS
Applicable over recommended operating ranges shown below unless otherwise noted:
VCC = +2.5V to +6.0V
Commercial (C): Tamb = 0˚C to +70˚C
Industrial (I): Tamb = -40˚C to +85˚C
Parameter
Symbol
Min.
Max.
Units Conditions
High level input voltage VIH1
2.0 VCC +1 V
VIH2
0.7 VCC VCC +1
V
Low level input voltage
VIL1
-0.3 0.8
V
VIL2
-0.3 0.2 VCC
V
Low level output voltage VOL1
— 0.4 V
VOL2
— 0.2 V
High level output voltage VOH1
2.4 — V
VOH2
VCC-0.2
—
V
Input leakage current
ILI
-10 10 µA
Output leakage current ILO
-10 10 µA
Pin capacitance
(all inputs/outputs)
CINT
— 7 pF
Operating current
ICC write
—
3 mA
ICC read
—
1 mA
500 µA
Standby current
ICCS
— 100 µA
30 µA
Note: This parameter is periodically sampled and not 100% tested.
VCC ≥ 2.7V
VCC < 2.7V
VCC ≥ 2.7V
VCC < 2.7V
IOL = 2.1 mA; VCC = 4.5V
IOL =100 µA; VCC = VCC Min.
IOH = -400 µA; VCC = 4.5V
IOH = -100 µA; VCC = VCC Min.
VIN = 0.1V to VCC
VOUT = 0.1V to VCC
(Note Note:)
Tamb = +25˚C, FCLK = 1 MHz
VCC = 5.5V
FCLK = 3 MHz; VCC = 5.5V
FCLK = 1 MHz; VCC = 3.0V
CLK = CS = 0V; VCC = 5.5V
CLK = CS = 0V; VCC = 3.0V
DS21131C-page 2
Preliminary
© 1996 Microchip Technology Inc.
|
PDF 파일 내의 페이지 : 총 12 페이지
제조업체: Fairchild Semiconductor
( fairchild )
9410A transistor
데이터시트 다운로드 :
[ 9410A.PDF ]
[ 9410A 다른 제조사 검색 ]
국내 전력반도체 판매점
상호 : 아이지 인터내셔날
전화번호 : 051-319-2877
[ 홈페이지 ]
IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈
( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )
전력반도체 문의 : 010-3582-2743
관련 데이터시트
9410A
Single N-Channel Enhancement Mode Field Effect Transistor - Fairchild Semiconductor
9410A
N-Channel Enhancement Mode Field Effect Transistor - Chino-Excel Technology