파트넘버.co.kr 74F807 데이터시트 PDF


74F807 반도체 회로 부품 판매점

Octal shift/count registered transceiver with adder and parity 3.State



Philips 로고
Philips
74F807 데이터시트, 핀배열, 회로
Philips Semiconductors FAST Products
Octal shift/count registered transceiver
with adder and parity (3–State)
Product specification
FAST 74F807
FEATURES
High speed parallel registers with
positive edge–triggered D–type
flip–flops
High speed full adder
8–bit parity generator
High impedance PNP inputs for light
bus loading
Center VCC and GND pins and con-
trolled output buffers minimize
ground–bounce problems
3–State glitch–free power–up and
power–down
Broadside pinout
DESCRIPTION
The 74F807 is a registered transceiver
that also has the capability to perform
count, shift, and add functions. It is also
has the capability to generate a parity
bit output. All of this is done within a
28–pin package.
The MR input is an overriding
asynchronous reset which forces the
STATOUT output low as well as the A
and B busses.
The A and B busses have separate OE
inputs (OEA, OEB]. These inputs have
no bearing on the internal functioning of
this device only on the output states.
Both OE pins are enabled low.
All operating modes, other than clear,
3–State, and the two hold modes re-
quire the rising edge of the clock. All
setup and hold times must be observed
for proper functioning.
Data on the internal register can be
switched on either the A or B ports for
output.
Depeding on the state of the select in-
puts (S0, S1, S2), and carry in/ serial in/
clock enable (CI/SI/CE), the 74F807 has
nine distinct operating modes:
1. Add mode w/carry in – the CI/SI/CE
input is used as a carry in signal and the
STATOUT output is the carry out signal.
(In add mode the COUT is NOT
registered. This means the carry output
signal appears at the STATOUT output
one clock prior to the related data.). In
this mode, the CI/SI/CE input is added
to the register contents and to the
inputs. (The adder uses only the An
inputs, not the Bn inputs.)
2. Add mode wo/carry in –– same as above
except the CI/SI/CE input is not included in
the addition.
3. Count w/count enable (count) –– the CI/SI/
CE input is now used as the count enable
input and the STATOUT output is terminal
count. In this mode the CI/SI/CE input must
be high to enable the count function. The
register contents are incremented by one.
4. Count w/count enable (hold) –– same as
above except no incrementing occurs.
5. Count wo/count enable –– same as num-
ber 3 except the CI/SI/CE input has no con-
trol over counting or holding.
6. Shift –– The CI/SI/CE input now becomes
the serial input and the STATOUT output
becomes the serial output. In this mode the
CI/SI/CE input is shifted into the Q0 register,
Q0 into the Q1 register etc. The Q7 register
is shifted into the STATOUT.
7. Load A inputs –– The CI/SI/CE input has
no bearing in either of the load modes. The
STATOUT output becomes the parity out.
The parity out is high for an odd number of
registered bits high, and low for even number
of registered bits high (even parity). In this
mode the An inputs are loaded into the
internal register and output to the B bus. If
OEA = low the internal register would wrap
around and be loaded again.
8. Load B inputs –– same as number 7
except the A and B busses are switched.
9. Hold –– Again the CI/SI/CE input is not
used; the STATOUT output is still the parity
out. In this mode either the A bus, B bus or
both can be held with the registered data. No
other operation is performed.
TYPE
74F807
TYPICAL fmax
115MHz
TYPICAL SUPPLY CURRENT (TOTAL)
155mA
ORDERING INFORMATION
DESCRIPTION
28–pin plastic DIP (300 mils)
28–pin SOL1
ORDER CODE
COMMERCIAL RANGE
VCC = 5V ±10%, Tamb = 0°C to +70°C
N74F807N
N74F807D
28–pin PLCC
N74F807A
Note to ordering information
1.Thermal mounting techiques are recommended. See SMD Process Applications (page 17) for a discussion of thermal consideration for surface
mounted devices.
June 18, 1991
1 853–1421 02931


74F807 데이터시트, 핀배열, 회로
Philips Semiconductors FAST Products
Octal shift/count registered transceiver
with adder and parity (3–State)
Product specification
FAST 74F807
INPUT AND OUTPUT LOADING AND FAN OUT TABLE
PINS
DESCRIPTION
74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW
An, Bn
Data I/O inputs
3.5/0.166
70µA/70µA
OEA, OEB
A output enable inputs
1.0/0.033
20µA/20µA
CI/SI/CE
Carry in/serial in/clock enable input
1.0/0.033
20µA/20µA
CP Clock input
1.0/0.033
20µA/20µA
MR Master reset input (active low)
1.0/0.033
20µA/20µA
Sn Select inputs
1.0/0.033
20µA/20µA
STATOUT
An, Bn
Status out output
Data I/O outputs
150/40
3mA/24mA
150/40
3mA/24mA
Note to input and output loading and fan out table
1. One (1.0) FAST unit load is defined as: 20µA in the high state and 0.6mA in the low state.
PIN CONFIGURATION
PIN CONFIGURATION PLCC
OEA 1
OEB 2
A0 3
A1 4
A2 5
A3 6
GND 7
GND 8
A4 9
A5 10
A6 11
A7 12
CI/SI/CE 13
CP 14
28 MR
27 STATOUT
26 B0
25 B1
24 B2
23 B3
22 VCC
21 B4
20 B5
19 B6
18 B7
17 S0
16 S1
15 S2
STAT
A1 A0 OEB OEA MR OUT B0
4 3 2 1 28 27 26
A2 5
25 B1
A3 6
24 B2
GND 7
23 B3
GND 8
A4 9
PLCC
22 VCC
21 B4
A5 10
20 B5
A6 11
19 B6
12 13 14 15 16 17 18
A7 CI/ CP S2 S1 S0 B7
SI/
CE
LOGIC SYMBOL
IEC/IEEE SYMBOL
3 4 5 6 9 10 11 12
A0 A1 A2 A3 A4 A5 A6 A7
1 OEA
2 OEB
13 CI/SI/CE
28 MR
STATOUT
B0 B1 B2 B3 B4 B5 B6 B7
27
26 25 24 23 22 20 19 18
VCC = Pin 22
GND = Pin 7, 8
13
EN3
17
0
16 M 1
15
15 STATUS
27
3 OUT
14
28 R
1 EN1
2 EN2
3 26
12
4 25
5 24
8 23
9 21
10 20
11 19
13 18
June 18, 1991
2




PDF 파일 내의 페이지 : 총 8 페이지

제조업체: Philips

( philips )

74F807 transceiver

데이터시트 다운로드
:

[ 74F807.PDF ]

[ 74F807 다른 제조사 검색 ]




국내 전력반도체 판매점


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877

[ 홈페이지 ]

IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈

( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )

전력반도체 문의 : 010-3582-2743



일반적인 전자부품 판매점


디바이스마트

IC114

엘레파츠

ICbanQ

Mouser Electronics

DigiKey Electronics

Element14


관련 데이터시트


74F804

Hex 2-input NAND drivers - Philips



74F805

Hex 2-input NOR drivers - Philips



74F807

Octal shift/count registered transceiver with adder and parity 3.State - Philips



74F808

Hex 2-input AND drivers - Philips