|
|
Número de pieza | PP0300SB | |
Descripción | (PP0640SA - PP0300SC) THYRISTOR SURGE SUPPRESSOR | |
Fabricantes | Protek Devices | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de PP0300SB (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
No Preview Available ! Only One Name Means ProTek’Tion™
PP0640SA
thru
PP3500SC
THYRISTOR SURGE SUPPRESSOR
APPLICATIONS
✔ T1/E1 Trunk & Line Card
✔ SLIC Line Card
✔ DBX Branch Exchange Switches
✔ FCC Part 68 Customer Premise Equipment
✔ Line Interface Modem
✔ xDSL Architecture Interface
✔ ISDN Architecture Interface
IEC COMPATIBILITY (EN61000-4)
✔ 61000-4-2 (ESD): Air - 15kV, Contact - 8kV
✔ 61000-4-4 (EFT): 40A - 5/50ns
✔ 61000-4-5 (Surge): 8/20µs - 95A, L4(Line-Gnd), 48A, L4(Line-Line) & 83A, L2(Power)
FEATURES
✔ Complies with: FCC Part 68, UL 1459, Bellcore 1089, ITU-K.20 & K.21
✔ UL File Recognition # E208219
✔ Peak Off-State Voltage from 25 to 300 Volts
✔ Surge Current Capability (See Table 1)
✔ ESD Protection > 40 kilovolts
✔ Low Capacitance for T1/E1 Trunk & Line Card Applications
✔ Bidirectional Configurations
✔ RoHS Compliant in Lead-Free Versions
MECHANICAL CHARACTERISTICS
✔ Molded Plastic DO-214AA Package
✔ Weight 2.5 grams (Approximate)
✔ Available in Tin-Lead or Lead-Free Pure-Tin Plating(Annealed)
✔ Solder Reflow Temperature:
Tin-Lead - Sn/Pb, 85/15: 240-245°C
Pure-Tin - Sn, 100: 260-270°C
✔ Flammability Rating UL 94V-0
✔ 12mm Tape and Reel Per EIA Standard 481
✔ Marking: Logo & Marking Code
DO-214AA
DEVICE SYMBOL
(BIDIRECTIONAL)
TABLE 1 - SURGE RATINGS
SERIES
I
PP
2 X 10µs
AMPS
IPP
8 X 20µs
AMPS
III
PP PP PP
10 X 160µs 10 X 560µs 10 X 1000µs
AMPS
AMPS
AMPS
SA 150 150 100 50
SB 300 300 150 100
SC 500 400 200 200
Note 1: Critital Rate of Rise for On-State Current (di/dt) and Off-State Voltage (dv/dt).
50
80
100
I
TSM
60 Hz
AMPS
20
32
60
di/dt dv/dt
AMPS/µs
V/µs
(See Note 1) (See Note 1)
500 2000
500 2000
500 2000
05081.R9 5/05
1 www.protekdevices.com
1 page APPLICATION NOTE
FIGURE 1: UL 1459 & FCC Part 68 - Metallic Protection
The TSS (Thyristor Surge Suppressor) device is located across the
tip-to-ring after a limiting resistor and fuse combination. RTIP and
RRING resistors are optional depending upon the TSS device selec-
tion. Without the resistors, the PP3100SB/SC is recommended.
However, with a resistance value of 7.5 Ohms for tip and ring, the
PP3100SA is recommended. Digital signals may use a lower TSS
device depending upon the total tip to ring voltage range. Selection
of the TSS device, either PPxxxxSA or SB/SC is based upon the
value of the tip and ring resistors. For the National Electric Code
(NEC) article 800, it is recommended that at least one fuse be used
in the tip or ring line for metallic surges. Fuses may be replaced with
a suitable Positive Temperature Coefficient (PTC) automatic
resettable current limiting device.
FIGURE 2 - UL 1459 & FCC Part 68 - Longitudinal Protection
There are two TSS devices, one located from tip-to-ground and one
ring-to-ground. For standard analog signals, the PP3100SA is
recommended with a typical resistor value for tip and ring of 15
Ohms. The PP3100SB/SC is recommended for resistor values of 7.5
Ohms each. The National Electric Code (NEC) article 800 requires
two fuse elements when connecting to ground. Fuses or a suitable
Positive Temperature Coefficient (PTC) automatic resettable current
limiting device may be used. The purpose of this circuit is to limit AC
power current from getting on the ground line causing any safety
hazard.
FIGURE 3 - UL 1459 & FCC Part 68 - Metallic & Longitudinal
Protection
Three equal TSS devices are used in this application for metallic (tip-
to-ring) and longitudinal (tip-to-ground and ring-to-ground) protec-
tion. For analog signals, the PP3100SB/SC is recommended. With a
resistance value of 15 Ohms for the tip and ring resistors, the
PP3100SA may be used. The National Electric Code (NEC) article
800 requires two fuse elements when connecting to ground. Fuses
or a suitable Positive Temperature Coefficient (PTC) automatic
resettable current limiting device may be used. This circuit is
recommended for protection against the Bellcore requirement: First
Level Lightning Surge Tests (Telecommunications Port), document #
GR-1089-CORE.
PP0640SA
thru
PP3500SC
Fuse
TIP
RTip
RING
RRing
To
Protected
Equipment
FIGURE 1 - Metallic Protection
RTip
TIP
To
Protected
Equipment
RING
RRing
FIGURE 2 - Longitudinal Protection
RTip
TIP
To
Protected
Equipment
RING
RRing
FIGURE 3 - Metallic & Longitudinal Protection
05081.R9 5/05
5 www.protekdevices.com
5 Page |
Páginas | Total 6 Páginas | |
PDF Descargar | [ Datasheet PP0300SB.PDF ] |
Número de pieza | Descripción | Fabricantes |
PP0300SB | (PP0640SA - PP0300SC) THYRISTOR SURGE SUPPRESSOR | Protek Devices |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |