파트넘버.co.kr JGC-4F 데이터시트 PDF


JGC-4F 반도체 회로 부품 판매점

SOLID STATE RELAY



ETC 로고
ETC
JGC-4F 데이터시트, 핀배열, 회로
JGC-4F
SOLID STATE RELAY
File No.: E133481
File No.: R2024431
File No.: CH0032705-2002A
Features
DC input-AC output for 2A load at 25
600 Volt blocking voltage
Photo isolation
Built-in snubber
Zero cross or random turn-on
Printed circuit board mount
INPUT (TA = 25•C)
Control voltage range
Must operate voltage
Must release voltage
Max. input current
05D
12D
24D
05D
12D
24D
OUTPUT
Load voltage range (@47 to 63Hz)
Load current range
Max. surge current (10ms)
Max. leakage current
Max. on-state voltage drop
Zero cross turn-on
Max. turn-on time
Random turn-on
Max. turn-off time
Transient overvoltage
Min. off-state dv/dt
Zero-crossover voltage
Min. power factor
4 to 6VDC
9.6 to 14.4VDC
19.2 to 28.8VDC
4VDC max.
9.6VDC max.
19.2VDC max.
1.0VDC min.
10mA
75 to 264VAC
0.1 to 2A
25Apk
1.5mA
1.5VAC
10ms
1ms
10ms
600Vpk max.
100V/µs min.
15V max.
0.5
GENERAL
Dielectric strength ( input to output ) 2000VAC min., 50/60Hz 1min.
Insulation resistance
1000M , min. (at 500VDC)
Max. Capacitance ( input to output )
5pF
Vibration durability
10 to 55HZ Double amplitude 1.5mm
Shock durability
1000m/s2
Ambient Operating
temperature Storage
-30 to +80
-30 to +100
Ambient Humidity
45% to 85%
Unit weight
6g
DESCRIPTION
This SPST-NO printed circuit board mount SIP SSR provides AC output
switching in a high density package.The JGC-4F's DC input is compatible
with 5, 12 and 24V logic systems .All models include an internal
snubber.The relays provide 2000Vrms opto-isolation,between input and
output. Encapsulation,thermally conductive epoxy.
PRECAUTIONS
1. Terminal arrangement
1 load
2
3(+)
0 180
AC line
Pulse width
Input signal
4( - )
Input signal turn off
Minimum 200µs
2. Soldering must be completed within 10 seconds at 260 or less
or within 5 seconds at 350 or less.
3. The SSR case serves to dissipate heat. Install the relays so that they
are adequately ventilated. If poor ventilation is unavoidable, reduce the
load current by half.
4. The input circuitry does not incorporate a circuit protecting the SSR
from being damaged due to a reversed connection. Make sure that the
polarity is correct when connecting the input lines.
5. When using the JGC-4F series for an AC load with a peak voltage of
more than 450V,connect the load terminals of the relay to an inrush
absorber(varistor). The recommended varistor voltage, 440 to 470V.
6. The load terminals are internally connected to a snubber circuit that
absorb noise. However, if wiring from these terminals is laid with or
placed in the same duct as high-voltage or power lines, noise may
be induced, causing the SSR to operate irregularly or malfunction.
7. When using the JGC-4F series in phase control applications, at a
phase control angle close to 180 degrees the relay's input signal turn
off at the trailing edge of the AC sine wave must be limited to end
200µs before AC zero cross. This assures that the relay has time
to switch off. Shorter times may cause loss of control at the following
half cycle.
HONGFA RELAY
ISO9001/QS9000/ISO14000 CERTIFIED
176


JGC-4F 데이터시트, 핀배열, 회로
ORDERING INFORMATION
JGC-4F / 12
D
Type
Input voltage 05 : 4 to 6VDC 12 : 9.6 to 14.4VDC 24 : 19.2 to 28.8VDC
Input Form D: DC
Zero Cross Function 0: Zero cross turn-on 1: Randm turn-on
Termination T: Same as TOSHIBA TSZXX48S, M: Same as OMRON G3MB
1
T
OUTLINE DIMENSIONS, WIRING DIAGRAM AND PC BOARD LAYOUT
JGC-4F/ D- T
Outline Dimensions
24 max.
6.5max.
PCB layout
2.54
Wiring Diagram
12
load
(+)3 4(_)
input
0.7 0.15
5.08 0.5
7.62 0.6
(2.5)
3.9 0.5
2.54 0.3
0.4 0.15
1.7 0.3
2.54
4-Ø1
(Bottom view)
JGC-4F/ D- M
24 max.
6.5max.
2.54
0.7 0.15
7.62 0.6
10.16 0.6
(2.5) 3.9 0.5
2.54 0.3
0.4 0.15
1.7 0.3
2.54 4-Ø1
12
load
(+)3 4(_)
input
CHARACTERISTICS CURVE
MAXIMUM LOAD CURRENT
MAXIMUM PERMISSIBLE NON-REPETITIVE
PULSE INPUT CURRENT
VS.AMBIENT TEMPERATURE PEAK SURGE CURRENT VS. CONTINUANCE TIME
VS. PULSE WIDTH
INPUT CURRENT
VS. AMBIENT TEMPERATURE
2.5
25
IT
1000
2.0 0 20
800 Tj=25•C F=50Hz
1.5
600
15
1.0
400
10
0.5
200
5
0
-30 -20 0 20 25 40 60 80 100
Ambient Temperature( )
0
0
10
100 1000 10000 1
Energizing Continuance Time(ms)
1.6
tw
Normalized to:
tw•100µs
1.4
1.2
1.0
0.8
NORMALIZED TO:
TA=25•C
2
5 10 20
50 100
Pulse Width Tw (µS)
0.6
-40 -20
0 20 40 60 80
Ambient Temperature( )
177




PDF 파일 내의 페이지 : 총 2 페이지

제조업체: ETC

( etc )

JGC-4F relay

데이터시트 다운로드
:

[ JGC-4F.PDF ]

[ JGC-4F 다른 제조사 검색 ]




국내 전력반도체 판매점


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877

[ 홈페이지 ]

IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈

( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )

전력반도체 문의 : 010-3582-2743



일반적인 전자부품 판매점


디바이스마트

IC114

엘레파츠

ICbanQ

Mouser Electronics

DigiKey Electronics

Element14


관련 데이터시트


JGC-4F

SOLID STATE RELAY - ETC