|
|
Número de pieza | IFX1963 | |
Descripción | 1.5A Low Dropout Linear Voltage Regulator | |
Fabricantes | Infineon Technologies | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de IFX1963 (archivo pdf) en la parte inferior de esta página. Total 25 Páginas | ||
No Preview Available ! IFX1963
1.5A Low Dropout Linear Voltage Regulator
IFX1963TBV
IFX1963TEV
Data Sheet
Rev. 1.0, 2013-02-25
Industrial Standard Power
1 page 2 Block Diagram
IFX1963
Block Diagram
IFX1963 ADJ
IN 2
EN 4
Bias
Voltage
reference
Error
Amplifier
Reverse Current
Protection
4 OUT
Over Current
Protection
Saturation
Control
Temperature
Protection
5 ADJ
Figure 1 Block Diagram
3
GND
Data Sheet
5 Rev. 1.0, 2013-02-25
5 Page IFX1963
Electrical Characteristics
Table 4 Electrical Characteristics: (cont’d)
VI = 2.5 V - 20 V, Tj = -40 °C to +125 °C, all voltages with respect to ground, positive current flowing out of the pin
(unless otherwise specified)
Pos. Parameter
Symbol
Limit Values Unit Conditions
Min. Typ. Max.
5.1.27 Quiescent Current in
Shutdown 9)
Iq,off – 0.01 1 µA VIN = 6 V; VEN = 0 V;
Tj ≤ 85 °C
5.1.28 Power Supply ripple rejection PSRR
10)
55 67
–
dB Tj = 25 °C;
fr = 120 Hz;
IOUT = 0.75 A;
VIN - VOUT = 1.5 V;
Vr = 0.5 Vpp
5.1.29 Output current limitation
IOUT
– 2 – A Tj = 25 °C;
VIN = 7 V; VOUT = 0 V
5.1.30
IOUT
1.6 – – A VIN = VOUT,nom + 1 V;
dVOUT = -0.1 V
5.1.31 Input Reverse Leakage
Current
IIN,rev – – 2 mA VIN = -20 V;
VOUT = 0 V
5.1.32 Reverse Output Current 1)11) IOUT,rev
–
300 600 µA
Tj = 25 °C;
VOUT = 1.21 V;
VIN = 0 V
5.1.33
– – 1 mA VOUT = 1.21 V;
VIN = 0 V
1) The IFX1963 is tested and specified for these conditions with the ADJ pin connected to the OUT pin.
2) For IFX1963 dropout voltage will be limited by the minimum input voltage specification under some output voltage/load
conditions.
3) Operating conditions are limited by maximum junction temperature. The regulated output voltage specification will not apply
for all possible combinations of input voltage and output current. When operating at maximum input voltage, the output
current range must be limited. When operating at maximum output current, the input voltage range must be limited.
4) To satisfy requirements for minimum input voltage, the IFX1963 is tested and specified for these conditions with an external
resistor divider (two 4.12 kΩ resistors) for an output voltage of 2.4 V. The external resistor divider will add a 300 µA DC
load on the output.
5) Dropout voltage is the minimum input to output voltage differential needed to maintain regulation at a specified output
current. In dropout, the output voltage will be equal to: VIN – VDR
6) GND pin current is tested with VIN = VOUT,nom + 1 V and a current source load.
7) ADJ pin bias current flows into the ADJ pin.
8) EN pin current flows into the EN pin.
9) Specified by design, tested at Tamb = 25 °C
10) Not subject to production test, specified by design.
11) Reverse output current is tested with the IN pin grounded and the OUT pin forced to the rated output voltage. The reverse
output current flows into the OUT pin.
Data Sheet
11 Rev. 1.0, 2013-02-25
11 Page |
Páginas | Total 25 Páginas | |
PDF Descargar | [ Datasheet IFX1963.PDF ] |
Número de pieza | Descripción | Fabricantes |
IFX1963 | 1.5A Low Dropout Linear Voltage Regulator | Infineon Technologies |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |