|
|
PDF AN0130 Data sheet ( Hoja de datos )
| Número de pieza | AN0130 | |
| Descripción | 8 Channel Power MOSFET Array Monolithic N-channel Enchancement Mode | |
| Fabricantes | Supertex Inc | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AN0130 (archivo pdf) en la parte inferior de esta página. Total 4 Páginas | ||
|
No Preview Available !
Everything You Always Wanted to Know
About the ICL8038
Application Note
November 1996
AN013.1
Author: Bill O’Neil
Introduction
The 8038 is a function generator capable of producing sine,
square, triangular, sawtooth and pulse waveforms (some at
the same time). Since its introduction, marketing and appli-
cation engineers have been manning the phones explaining
the care and feeding of the 8038 to customers worldwide.
This experience has enabled us to form articulate responses
to the most frequently asked questions. So, with data sheet
and breadboard in hand, read on and be enlightened.
Question 1
I want to sweep the frequency externally but can only get a
range of 100:1 (or 50:1, or 10:1). Your data sheet says
1000:1. How much sweep range can I expect?
Answer
Let’s look at what determines the output frequency. Start by
examining the circuit schematic at pin 8 in the upper left hand
corner. From pin 8 to pin 5 we have the emitter-base of NPN
Q1 and the emitter-base of PNP Q2. Since these two diode
drops cancel each other (approximately), the potential at pins
8, 5, and 4 are the same. This means that the voltage from V+
to pin 8 is the same as the voltage across external resistors
RA and RB. This is a textbook example of a voltage across
two resistors which produce two currents to charge and dis-
charge a capacitor between two fixed voltages. This is also a
linear system. If the voltage across the resistors is dropped
from 10V to 1V, the frequency will drop by 10:1. Changing
from 1V to 0.1V will also change the frequency by 10:1.
Therefore, by causing the voltage across the external resis-
tors to change from say 10V to 10mV, the frequency can be
made to vary at least 1000:1. There are, however, several fac-
tors which make this large sweep range less than ideal.
Question 2
You say I can vary the voltage on pin 8 (FM sweep input) to
get this large range, yet when I short pin 8 to V+ (pin 6), the
ratio is only around 100:1.
Answer
This is often true. With pin 8 shorted to V+, a check on the
potentials across the external RA and RB will show 100mV
or more. This is due to the VBE mismatch between Q1 and
Q2 (also Q1 and Q3) because of the geometries and current
levels involved. Therefore, to get smaller voltages across
these resistors, pin 8 must be raised above V+.
Question 3
How can I raise pin 8 above V+ without a separate power
supply?
Answer
First of all, the voltage difference need only be a few hundred
millivolts so there is no danger of damaging the 8038. One
way to get this higher potential is to lower the supply voltage
on the 8038 and external resistors. The simplest way to do
this is to include a diode in series with pin 6 and resistors RA
and RB. See Figure 1. This technique should increase the
sweep range to 1000:1.
0.1µF
4.7K
RB
1N457
DUTY
CYCLE
1K
4.7K
RA
+15V
15K
100K
FREQUENCY
LOG POT
10M
5
8
7
10
46
9
3
2
11 12
0.0047µF
DISTORTION
100K
-15V
FIGURE 1. VARIABLE AUDIO OSCILLATOR, 20Hz TO 20kHz
Question 4
O.K., now I can get a large frequency range, but I notice that
the duty cycle and hence my distortion changes at the low-
est frequencies.
Answer
This is caused partly by a slight difference in the VBEs of Q2
and Q3. In trying to manufacture two identical transistors, it is
not uncommon to get VBE differences of several millivolts or
more. In the standard 8038 connection with pins 7 and 8 con-
nected together, there are several volts across RA and RB and
this small mismatch is negligible. However, in a swept mode
with the voltage at pin 8 near V+ and only tens of millivolts
across RA and RB, the VBE mismatch causes a larger mis-
match in charging currents, hence the duty cycle changes. For
lowest distortion then, it is advisable to keep the minimum
voltage across RA and RB around 100mV. This would of
course, limit the frequency sweep range to around 100:1.
1 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999
1 page | ||
| Páginas | Total 4 Páginas | |
| PDF Descargar | [ Datasheet AN0130.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AN013 | Everything You Always Wanted to Know About the ICL8038 |  Intersil Corporation |
| AN0130 | 8 Channel Power MOSFET Array Monolithic N-channel Enchancement Mode | Supertex Inc |
| AN0130NA | 8 Channel Power MOSFET Array Monolithic N-channel Enchancement Mode | Supertex Inc |
| AN0130NB | 8 Channel Power MOSFET Array Monolithic N-channel Enchancement Mode | Supertex Inc |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |