파트넘버.co.kr WD3148 데이터시트 PDF


WD3148 반도체 회로 부품 판매점

White LED Driver



WillSEMI 로고
WillSEMI
WD3148 데이터시트, 핀배열, 회로
WD3148
White LED Driver with PWM Brightness Control
in Tiny Package
WD3148
Http://www.sh-willsemi.com
With a 40-V rated integrated power switch MOSFET,
the WD3148 is a boost converter that drives up to 10
White LEDs in series. The WD3148 operates at
600kHz fixed switching frequency to reduce output
ripple, improve conversion efficiency, and allows for
the use of small external components.
FB 1
COMP 2
GND 3
6 VIN
5 EN
4 LX
The default Full-Scale White LED current is set by an
external sensor resistor with regulated 200mV
feedback voltage, as shown in typical application.
During operation, the LED current can be controlled
using the Pulse Width Modulation (PWM) signal
applied on the EN pin, through which the PWM
Duty-Cycle determines the feedback reference voltage
and then the White LED current. In PWM mode, the
WD3148 does not burst the LED current; therefore, it
does not generate audible noises on the ceramic
output capacitor. For maximum protection, the device
features integrated open LED protection that disables
the WD3148 to prevent the output voltage from
exceeding the absolute maximum ratings during open
LED conditions.
The WD3148 is available in a PCB space saving DFN
2mm x 2mm-6L Package with bottom thermal pad.
Standard product is Pb-free and Halogen-free.
DFN 2mm x 2mm-6L
Pin configuration (Top view)
3148
Y
W
Marking
= Device Code
= Year Code
= Week Code
Order information
Features
2.7V~5.5V Input voltage range
38V Open LED Protection
200mV Reference Voltage
600kHz Switching frequency
Up to 91% Efficiency
PWM Brightness Control
PWM Dimming Duty ranges from 0.3% to 100%
Built-in Soft-Start and Over-Current limit
Device
Package
Shipping
WD3148D-6/TR DFN-2x2-6L 3000/Reel&Tape
Applications
Smart Phones
Tablets
Portable games
Will Semiconductor Ltd.
1 Apr 12, 2016 - Rev. 1.0


WD3148 데이터시트, 핀배열, 회로
Typical applications
WD3148
L1 D1
VIN 10μH~22μH WSB5543W VOUT
CIN
1μF
VIN LX
ON/OFF
Dimming Control
EN
GND
COMP
FB
COUT
1μF/50V
CCOMP
220nF
10 LEDs
RSET
Pin descriptions
Symbol
FB
COMP
GND
LX
EN
VIN
Thermal Pad
Pin No.
1
2
3
4
5
6
Bottom
Descriptions
Feedback pin for LED current. Connect the sense resistor from FB to
GND
Output of the Error Amplifier. Connect an external capacitor to this pin
to compensate the converter
Ground
Switch pin. Connect the inductor between VIN and LX. This pin is also
used to sense output voltage for Open LED Protection
Enable pin of boost converter. It also can be used for PWM dimming
control
Power supply. Connect VIN to a supply voltage between 2.7V and 5.5V
The exposed thermal pad should be soldered to the analog ground
plane. If possible, use the thermal via to connect to ground plane
Will Semiconductor Ltd.
2 Apr 12, 2016 - Rev. 1.0




PDF 파일 내의 페이지 : 총 17 페이지

제조업체: WillSEMI

( willsemi )

WD3148 led

데이터시트 다운로드
:

[ WD3148.PDF ]

[ WD3148 다른 제조사 검색 ]




국내 전력반도체 판매점


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877

[ 홈페이지 ]

IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈

( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )

전력반도체 문의 : 010-3582-2743



일반적인 전자부품 판매점


디바이스마트

IC114

엘레파츠

ICbanQ

Mouser Electronics

DigiKey Electronics

Element14


관련 데이터시트


WD3148

White LED Driver - WillSEMI