|
|
PDF ATP350G01 Data sheet ( Hoja de datos )
| Número de pieza | ATP350G01 | |
| Descripción | Standard LCD Module | |
| Fabricantes | Kentec Electronics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ATP350G01 (archivo pdf) en la parte inferior de esta página. Total 19 Páginas | ||
|
No Preview Available !
FS-K350QVG-V2-F
15/Jul/2010
PAGE 1 OF 19
K350QVG-V2-F
ATP350G01
Product
Standard LCD Module
320 x RGB x 240 Dots
3.5”262K colors TFT display
Wide temperature
With white LED backlight
With Touch Panel
Kentec Electronics (Displays) Limited
URL: http://www.kentecdisplay.com
E-mail: [email protected]; [email protected]
1 page  
FS-K350QVG-V2-F
15/Jul/2010
PAGE 5 OF 19
Figure 1: Outline Drawing
5 Page 
FS-K350QVG-V2-F
15/Jul/2010
PAGE 11 OF 19
water droplets, moisture condensation or a current flow in a high-humidity environment.
6. Install the LCD Module by using the mounting holes. When mounting the LCD module make sure it is
free of twisting, warping and distortion. In particular, do not forcibly pull or bend the I/O cable or the
backlight cable.
7. Don’t disassemble the LCM.
8. To prevent destruction of the elements by static electricity, be careful to maintain an optimum work
environment.
- Be sure to ground the body when handling the LCD modules.
- Tools required for assembling, such as soldering irons, must be properly grounded.
- To reduce the amount of static electricity generated, do not conduct assembling and other work
under dry conditions.
- The LCD module is coated with a film to protect the display surface. Exercise care when peeling
off this protective film since static electricity may be generated.
9. Do not alter, modify or change the the shape of the tab on the metal frame.
10. Do not make extra holes on the printed circuit board, modify its shape or change the positions of
components to be attached.
11. Do not damage or modify the pattern writing on the printed circuit board.
12. Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector
13. Except for soldering the interface, do not make any alterations or modifications with a soldering iron.
14. Do not drop, bend or twist LCM.
10.2 Cautions for installing and assemabling if the module has Touch Panel
1. Use a buffer material (Gasket) between the touch panel and Front-case to protect damage and wrong
operating. The dimension of the buffer material’s edge between the TP V.A. edge is Min. 0.3mm.
2. We recommend to design a case that it can’t over the boundary of the active area Max. 0.5mm in order
to prevent an operation at outside of the active area which can’t guarantee the specified durability,
11 Page | ||
| Páginas | Total 19 Páginas | |
| PDF Descargar | [ Datasheet ATP350G01.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ATP350G01 | Standard LCD Module | Kentec Electronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |