파트넘버.co.kr IG135-15 데이터시트 PDF


IG135-15 반도체 회로 부품 판매점

High Isolation IGBT Driver DC/DC Converters



MicroPower Direct 로고
MicroPower Direct
IG135-15 데이터시트, 핀배열, 회로
IG100 Series
High Isolation
IGBT Driver
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
Operates With xx962 Drivers
Independent Outputs
3,000 VAC Isolation
Miniature SIP Case
>3.5 MHour MTBF
5 Standard Models
LOW COST!!
Input
Parameter
Supply Voltage Range
Input Filter
Output
Parameter
Line Regulation, See Note 1
Conditions
Min. Typ.
See Model Selection Guide
Internal Capacitor
Max.
Conditions
Min. Typ. Max.
For Vin Change of 1%
±1.3 ±1.5
IG120-12
100 200
IG120-12W
100 200
Units
Units
%
Ripple & Noise (20 MHz)
IG120-15
80 150 mV P - P
IG135-15
50 150
IG120-24
150 300
Efficiency
80 %
Output Short Circuit, See Note 3
Continuous (Autorecovery)
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
60 Seconds 3,000
VAC
Isolation Resistance
1,000
M
www.DataSheet.net/
IG120-12
6.6
IG120-12W
10
Isolation Capacitance, 1 kHz/1V
IG120-15
6.6
pF
IG135-15
8.0 10
IG120-24
6.6
Switching Frequency
550 kHz
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +85
ºC
Storage Temperature Range
-50
+125
ºC
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95 %
Physical
Case Size
0.768 x 0.386 x 0.492 Inches (19.50 x 9.80 x 12.50 mm)
Case Material
Non-Conductive Black Plastic (UL94-V0)
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Weight
Reliability Specifications
Parameter
MTBF
Absolute Maximum Ratings
0.195 Oz (5.5g)
Conditions
Min. Typ. Max.
MIL HDBK 217F, 25ºC, Gnd Benign 3.5
Units
MHours
T: (781) 344-8226
F: (781) 344-8481
W: www.micropowerdirect.com
Parameter
Max Supply Voltage (1 Sec)
Conditions
Min. Typ. Max.
IG120-12
13
IG120-12W
15
IG120-15
16
IG135-15
16
Units
VDC
IG120-24
26
Lead Temperature
1.5 mm From Case For 10 Sec
300 ºC
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
Datasheet pdf - http://www.DataSheet4U.co.kr/


IG135-15 데이터시트, 핀배열, 회로
Model Selection Guide
www.micropowerdirect.com
Model
Number
Input (Supply)
Voltage (VDC)
Nom. Range
Output 1
Voltage (VDC) Current
Min. Nom. Max. (mA Max)
Current
(mA, Min)
Output 2
Voltage (VDC) Current
Min. Nom. Max. (mA Max)
Current
(mA, Min)
Output
Load
Regulation
(%)
Maximum
Capacitive
Load
(µF)
Fuse Rating
Slow-Blow
(mA)
IG120-12 12 11.6 - 12.4 14.0 15.0 16.0 80.0 0.0 -7.0 -9.0 -10.0 40.0 0.0
12
470 1,000
IG120-12W 12 9.0 - 15.0 14.0 15.0 16.0 100.0 0.0 -7.0 -8.0 -9.0 80.0 0.0
12
470 1,000
IG120-15 15 14.5 - 15.5 14.0 15.0 16.0 80.0 0.0 -7.0 -8.7 -10.0 40.0 0.0
18
470 1,000
IG136-15 15 14.5 - 15.5 16.5 17.0 18.0 80.0 0.0 -7.0 -8.7 -10.0 40.0 0.0
18
470 1,000
IG120-24 24 23.3 - 24.7 14.0 15.0 16.0 80.0 0.0 -7.0 -9.0 -10.0 40.0 0.0
12
470 1,000
The IG100 series is designed
to operate with the IGD962
IGBT driver.
Typical Connection
Notes:
1. Line regulation for model IG120-12W is given for a
VIN change of 25%.
2. Load regulation is measured from 10% load to full
load. Load regulation is specified for the primary
output (output 1). Load regulation of output 2 may
vary slightly.
3. Operation at no-load will not damage these units.
However, they may not meet all specifications.
4. If output 2 is not used, it should be left open.
5. A short circuit fault that lasts over 10 minutes could
damage the unit due to an over temperature fault.
6. It is recommended that a fuse be used on the input of a
power supply for protection. See the Model Selection
table above for the correct rating.
Mechanical Dimensions
Connection Notes:
1. For model IG120-24, C1 is a 100 µF/65V.
2. Capacitors C1, C2 and C3 should be mounted as close
www.DataSheet.net/
to the unit as possible. To ensure peak gate current,
these capacitors should have a low ESR.
3. The trace (or wire) between the DC/DC and the driver
circuit should be as short as possible.
4. The average output power of the driver circuit must
be lower than output power of the DC/DC.
Pin Connections
Pin Function
1 +Vin
2 Gnd
5 Vout 2
6 Common
7 Vout 1
Notes:
All dimensions are typical in inches (mm)
Tolerance x.xx = ±0.01 (±0.25)
Pin 1 is marked by a “dot” or indentation on the side of the unit
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: [email protected]
Datasheet pdf - http://www.DataSheet4U.co.kr/




PDF 파일 내의 페이지 : 총 2 페이지

제조업체: MicroPower Direct

( micropower )

IG135-15 igbt

데이터시트 다운로드
:

[ IG135-15.PDF ]

[ IG135-15 다른 제조사 검색 ]




국내 전력반도체 판매점


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877

[ 홈페이지 ]

IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈

( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )

전력반도체 문의 : 010-3582-2743



일반적인 전자부품 판매점


디바이스마트

IC114

엘레파츠

ICbanQ

Mouser Electronics

DigiKey Electronics

Element14


관련 데이터시트


IG135-15

High Isolation IGBT Driver DC/DC Converters - MicroPower Direct