|
|
PDF A2547 Data sheet ( Hoja de datos )
| Número de pieza | A2547 | |
| Descripción | Protected Quad Driver | |
| Fabricantes | Allegro MicroSystems | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de A2547 (archivo pdf) en la parte inferior de esta página. Total 9 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
A2547
Protected Quad Driver
Last Time Buy
These parts are in production but have been determined to be
LAST TIME BUY. This classification indicates that the product is
obsolete and notice has been given. Sale of this device is currently
restricted to existing customer applications. The device should not be
purchased for new design applications because of obsolescence in the
near future. Samples are no longer available.
Date of status change: May 2, 2005
Deadline for receipt of LAST TIME BUY orders: October 28, 2005
Recommended Substitutions:
NOTE: For detailed information on purchasing options, contact your
local Allegro field applications engineer or sales representative.
Allegro MicroSystems, Inc. reserves the right to make, from time to time, revisions to the anticipated product life cycle plan for a
product to accommodate changes in production capabilities, alternative product availabilities, or market demand. The information
included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor
for any infringements of patents or other rights of third parties which may result from its use.
1 page  
2547
PROTECTED
QUAD POWER DRIVER
NORMAL LAMP IN-RUSH CURRENT
NOT TO SCALE
CURRENT LIMIT
SHORT CIRCUIT
THERMAL SHUTDOWN
THERMAL HYSTERESIS
TIME
Dwg. WP-005A
CIRCUIT DESCRIPTION AND APPLICATION
These devices monitor their outputs for open or shorted conditions.
Both conditions are sensed by comparing the input and output states.
Note that the FAULT output is operational only if the ENABLE input is
high. When a fault condition is sensed, the FAULT output will go to a
low state. An external FAULT output filter capacitor (0.1µF) is recom-
mended to eliminate erroneous switching.
INCANDESCENT LAMP DRIVER
High incandescent lamp turn-ON/in-rush currents can contribute to
poor lamp reliability and destroy semiconductor lamp drivers.
Warming (parallel) or current-limiting (series) resistors protect both
driver and lamp but use significant power either when the lamp is OFF
or when the lamp is ON, respectively. Lamps with steady-state current
ratings up to 600 mA can be driven without the need for warming or
current-limiting resistors, if lamp turn-ON time is not a concern.
When an incandescent lamp is initially turned ON, the cold filament
is at minimum resistance and would normally allow a 10x to 12x in-rush
current. With these drivers, during turn-ON, the high in-rush current is
sensed by the internal low-value sense resistor, drive current to the
output stage is diverted by the shunting transistor, the output stage
operates in a linear mode, and the load current is limited to approxi-
mately 1.3 A. During lamp warmup, the filament resistance increases
to its maximum value, the output driver goes into saturation and applies
maximum rated voltage to the lamp.
INDUCTIVE LOAD DRIVER
With the addition of external clamp diodes, bifilar (unipolar)
stepper motors and other inductive loads can be driven directly.
The external diodes prevent damage to the output transistors by
suppressing the high-voltage spikes that occur when turning
OFF an inductive load. For rapid current decay (fast turn-OFF speeds),
the use of Zener diodes will raise the flyback voltage and improve
performance. However, the peak voltage must not exceed the speci-
fied minimum sustaining voltage (VSUPPLY + VZ + VF ≤ VOUT(SUS)).
OVER-CURRENT CONDITIONS
In the event of a shorted load, or stalled motor, the load current
will attempt to increase. As described above, the drive current to the
affected output stage is linearly reduced (limiting the load current to
about 1.3 A), causing the output stage to go linear. As the junction
temperature of the output stage increases, the thermal shutdown circuit
will shut OFF the affected output. If the fault condition is corrected, the
output driver will return to its normal saturated condition.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
5 Page | ||
| Páginas | Total 9 Páginas | |
| PDF Descargar | [ Datasheet A2547.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| A2543B | LOW PROFILE ANTENNA |  Comtelco |
| A2543W | LOW PROFILE ANTENNA | Comtelco |
| A2547 | Protected Quad Driver | Allegro MicroSystems |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |