|
|
PDF 81006 Data sheet ( Hoja de datos )
| Número de pieza | 81006 | |
| Descripción | High Level Analog Switches With Drivers/ Monolithic Silicon | |
| Fabricantes | Maxim Integrated | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de 81006 (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
|
No Preview Available !
REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
F Add peak current to absolute maximum ratings. Editorial changes throughout.
G Changes in accordance with NOR 5962-R144-95.
H Make corrections to the switch operation table in 3.3.1. Update boilerplate to
reflect current requirements. -rrp
92-11-24
95-10-20
03-03-10
APPROVED
M. A. FRYE
M. A. FRYE
R. MONNIN
CURRENT CAGE CODE 67268
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
REV
HH
SHEET
12
PREPARED BY
Gary J. Zahn
CHECKED BY
William E. Sharp
APPROVED BY
N. A. Hauck
DRAWING APPROVAL DATE
81-10-01
HHHHHHHHHH
3 4 5 6 7 8 9 10 11 12
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
MICROCIRCUIT, LINEAR, CMOS, HIGH LEVEL
ANALOG SWITCHES WITH DRIVERS,
MONOLITHIC SILICON
AMSC N/A
REVISION LEVEL
H
SIZE
A
CAGE CODE
14933
SHEET
DSCC FORM 2233
APR 97
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
1 OF
12
81006
5962-E243-03
1 page  
TABLE I. Electrical performance characteristics.
Conditions
Test
Symbol
-55°C ≤ TA ≤ +125°C
VCC = ±15 V
Group A
subgroups
unless otherwise specified
Drain source “ON”
resistance
RDS VD = -10 V, IS = 10 mA,
VD = 10 V, IS = -10 mA,
Channel “ON” leakage
current
ID(ON)
Drain “OFF” leakage current ID(OFF)
Source “OFF” leakage
current
IS(OFF)
Input current, input voltage
low
Input current, input voltage
high
Positive supply current
IIL
IIH
+ICC
VD = -7.5 V, IS = 10 mA,
VCC = ±10 V 2/
VD = 7.5 V, IS = -10 mA,
VCC = ±10 V 2/
VS = VD = 10 V,
See 3.3.1 for VIN
VS = VD = -10 V,
See 3.3.1 for VIN
VS = -10 V, VD = 10 V,
See 3.3.1 for VIN
VS = 10 V, VD = -10 V,
See 3.3.1 for VIN
VS = 10 V, VD = -10 V,
See 3.3.1 for VIN
VS = -10 V, VD = 10 V,
See 3.3.1 for VIN
VIN = 0 V
VIN = 2.4 V, 5 V
VIN = 0 V, 5 V
Negative supply current -ICC VIN = 0 V, 5 V
1, 3
2
1, 3
2
1, 3
2
1, 3
2
1, 3
2
1, 3
2
2, 3
1
2, 3
1
2, 3
1
2, 3
1
2, 3
1
2, 3
1
1, 3
2
1, 3
2
1, 3
2
1
2, 3
1, 3
2
1
2, 3
Device
type
Limits
1 - 16
Min
17 - 22
1 - 16
17 - 22
All
All -200
-2
-200
-2
All -100
-1
-100
-1
All -100
-1
-100
-1
All -1
-10
All -1
-1
1-8
9 - 22
1-8
9 - 22
-10
-100
-200
-300
Max
75
150
45
50
75
150
45
50
75
150
75
150
200
2
200
2
100
1
100
1
100
1
100
1
1
1
1
10
10
100
200
300
Unit
Ω 1/
nA
nA
nA
µA
µA
µA
µA
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
H
81006
SHEET
5
5 Page 
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-
38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535,
appendix A.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
4. QUALITY ASSURANCE PROVISIONS
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
test method 1015 of MIL-STD-883.
(2) TA = +125°C, minimum.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-
883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Group A inspection.
a. Tests shall be as specified in table II herein.
b. Subgroups 4, 5, 6, 7, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
H
81006
SHEET
11
11 Page | ||
| Páginas | Total 15 Páginas | |
| PDF Descargar | [ Datasheet 81006.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| 81006 | High Level Analog Switches With Drivers/ Monolithic Silicon | Maxim Integrated |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |