|
|
PDF RE46C122 Data sheet ( Hoja de datos )
| Número de pieza | RE46C122 | |
| Descripción | CMOS Ionization Smoke Detector ASIC | |
| Fabricantes | Microchip | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de RE46C122 (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
|
No Preview Available !
R&E International
A Subsidiary of Microchip Technology Inc.
RE46C122
CMOS Ionization Smoke Detector ASIC with Interconnect and Timer Mode
Product Specification
General Description
The RE46C122 is low power CMOS ionization type
smoke detector IC. With few external components this
circuit will provide all the required features for an
ionization type smoke detector.
An internal oscillator strobes power to the smoke
detection circuitry for 10.5mS every 1.66 seconds to
keep standby current to a minimum. A check for a low
battery condition is performed every 40 seconds when
in standby. The temporal horn pattern supports the
NFPA 72 emergency evacuation signal.
An interconnect pin allows multiple detectors to be
connected such that when one units alarms all units will
sound.
An internal 10 minute timer allows for a separate button
to be used for reduced sensitivity mode.
Although this device was designed for smoke detection
utilizing an ionization chamber it could be used in a
variety of security applications.
The RE46C122 is recognized by Underwriters
Laboratories for use in smoke detectors that comply
with specification UL217 and UL268.
Features
• >1500V ESD Protection (HBM) on all Pins
• Guard Outputs for Ion Detector Input
• +/-0.75pA Detect Input Current
• Internal Reverse Battery Protection
• Low Quiescent Current Consumption (<6.5uA)
• Available in 16L PDIP or 16L N SOIC
• Internal Low Battery Detection
• Power Up Low Battery Test
• Interconnect up to 40 Detectors
• 10 Minute Timer for Sensitivity Control
• Compatible with Allegro A5367
• UL Recognized per File S24036
• Available in Standard Packaging or RoHS
Compliant Pb Free Packaging.
Pin Configuration
TSTART
IO
LBADJ
TSTROBE
LED
VDD
RBIAS
FEED
1
2
3
4
5
6
7
8
16 GUARD2
15 DETECT
14 GUARD1
13 VSEN
12 OSCAP
11 HS
10 HB
9 VSS
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Supply Voltage
Input Voltage Range Except FEED, IO
FEED Input Voltage Range
IO Input Voltage Range
Reverse Battery Time
Input Current except FEED
Operating Temperature
Storage Temperature
Maximum Junction Temperature
SYMBOL
VDD
Vin
Vinfd
Vio1
TRB
Iin
TA
TSTG
TJ
VALUE
15
-.3 to Vdd +.3
-10 to +22
-.3 to 17
5
10
-10 to 60
-55 to 125
150
UNITS
V
V
V
V
S
mA
°C
°C
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress
ratings only and operation at these conditions for extended periods may affect device reliability.
This product utilizes CMOS technology with static protection; however proper ESD prevention procedures should be used when
handling this product. Damage can occur when exposed to extremely high static electrical charge.
© 2009 Microchip Technology Inc.
DS22173B-page 1
1 page  
RE46C122
CMOS Ionization Smoke Detector ASIC with
Interconnect and Timer Mode
Product Specification
R&E International
A Subsidiary of Microchip Technology Inc.
DEVICE DESCRIPTION and APPLICATION NOTES
Internal Timing – With external components as indicated on the application drawing the period of the oscillator is
nominally 1.67 seconds in standby. Every 1.66 seconds the detection circuitry is powered up for 10.5mS and the
status of the smoke comparator is latched. In addition every 40 seconds the LED driver is turned on for 10.5mS
and the status of the low battery comparator is latched. The smoke comparator status is not checked during the
low battery test, during the low battery horn warning chirp, or when the horn is on due to an alarm condition.
If an alarm condition is detected the oscillator period increases to 41.5mS.
Due to the low currents used in the oscillator the capacitor on pin 12 should be a low leakage type. Oscillator
accuracy will depend mainly on the tolerance of the RBIAS resistor and OSCAP capacitor.
Smoke Detection Circuit – The smoke comparator compares the ionization chamber voltage to a voltage derived
from a resistor divider across VDD. This divider voltage is available externally on pin 13 (VSEN). When smoke is
detected this voltage is internally increased by 130mV nominal to provide hysteresis and make the detector less
sensitive to false triggering.
Pin 13 (VSEN) can be used to modify the internal set point for the smoke comparator by use of external resistors
to VDD or VSS. Nominal values for the internal resistor divider are indicated on the block diagram. These internal
resistor values can vary by up to ±20% but the resistor matching should be <2% on any one device. Transmission
switches on VSEN and LBADJ prevent any interaction from the external adjustment resistors.
The guard amplifier and outputs are always active and will be within 50mV of the DETECT input to reduce surface
leakage. The guard outputs also allow for measurement of the DETECT input without loading the ionization
chamber.
Low Battery Detection - An internal reference is compared to the voltage divided VDD supply. The battery can be
checked under load via the LED low side driver output since low battery status is latched at the end of the 10.5mS
LED pulse. Pin 3 (LBADJ) can be used to modify the low battery set point by placing a resistor to VDD or VSS.
Transmission switches on VSEN and LBADJ prevent any interaction from external adjustment resistance.
LED Pulse – The LED is pulsed on for 10.5mS every 40S in standby. In alarm the LED is pulsed on for 10.5mS
every 1S.
Interconnect – Pin 2 (IO) provides the capability to common many detectors in a single system. If a single unit
goes into alarm the IO pin is driven high. This high signal causes the interconnected units to alarm. The LED
flashes every 1S for 10.5mS on the signaling unit and is inhibited on the units that are in alarm due to the IO
signal. An internal sink device on the IO pin helps to discharge the interconnect line. This charge dump device is
active for 1 clock cycle after the unit exits the alarm condition (1.67S).
The interconnect input has a 500mS nominal digital filter. This allows for interconnection to other types of alarms
(carbon monoxide for example) that may have a pulsed interconnect signal.
Testing – At power up all internal registers are reset. The low battery set point can be tested at power up by
holding FEED and OSCAP low at power up. HB will change state as VDD passes through the low battery set
point. By holding pin 12 (OSCAP) low the internal power strobe is active. Functional testing can be accelerated by
driving pin 12 with a 4 kHz square wave however the 10.5mS strobe period must be maintained for proper
operation of the analog circuitry. Please refer to the timing diagrams.
Timer Mode – The transition of pin 1 (TSTART) from a high to low level initiates a ten minute timer. During this 10
minute period the open drain NMOS on pin 4 (TSTROBE) is strobed on with the internal clock. A resistor
connected to this pin could be used to modify the detector sensitivity for the timer period.
© 2009 Microchip Technology Inc.
DS22173B-page 5
5 Page | ||
| Páginas | Total 10 Páginas | |
| PDF Descargar | [ Datasheet RE46C122.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| RE46C120 | CMOS Ionization Smoke Detector ASIC |  R & E International |
| RE46C121 | CMOS Ionization Smoke Detector ASIC | R & E International |
| RE46C122 | CMOS Ionization Smoke Detector ASIC | Microchip |
| RE46C126 | CMOS Ionization Smoke Detector ASIC | R & E International |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |