|
|
PDF KX-TDA600CE Data sheet ( Hoja de datos )
| Número de pieza | KX-TDA600CE | |
| Descripción | Hybrid IP-PBX Service Manual | |
| Fabricantes | Panasonic | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de KX-TDA600CE (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
ORDER NO. KMS0510151CE
Hybrid IP-PBX
KX-TDA600CE
(for Europe)
IMPORTANT INFORMATION ABOUT LEAD FREE, (PbF), SOLDERING
If lead free solder was used in the manufacture of this product the printed circuit boards will be marked PbF.
Standard leaded, (Pb), solder can be used as usual on boards without the PbF mark.
When this mark does appear please read and follow the special instructions described in this manual on the use of PbF and how
it might be permissible to use Pb solder during service and repair work.
© 2005 Panasonic Communications Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
1 page  
KX-TDA600CE
2 FOR SERVICE TECHNICIANS
ICs and LSIs are vulnerable to static electricity.
When repairing, the following precautions will help prevent recurring malfunctions.
1. Cover the plastic parts boxes with aluminum foil.
2. Ground the soldering irons.
3. Use a conductive mat on the worktable.
4. Do not touch IC or LSI pins with bare fingers.
3 CAUTION
3.1. NOTE
When you note the serial number, write down all of the 11 digits.
The serial number may be found on the label affixed to the bottom of the unit.
3.2. SAFETY PRECAUTIONS
1. Before servicing, unplug the power cord to prevent an electric shock.
2. When replacing parts, use only the manufacturer´s recommended components for safety.
3. Check the condition of the power cord. Replace if wear or damage is evident.
4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.
5. Before returning the serviced equipment to the customer, be sure to perform the following insulation resistance test to prevent
the customer from being exposed to shock hazards.
3.3. INSULATION RESISTANCE TEST
1. Unplug the power cord and short the two prongs of the plug with a jumper wire.
2. Turn on the power switch.
3. Measure the resistance value with ohmmeter between the jumpered AC plug and each exposed metal cabinet part, such as
screw threads, control shafts, handle brackets, etc.
Note:
Some exposed parts may be isolated from the chassis by design. These will read infinity.
4. If the measurement is outside the specified limits, there is a possibility of shock hazard. The equipment should be repaired and
rechecked before it is returned to the customer.
3.4. BATTERY CAUTION
1. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s Instructions.
2. The lithium battery is a critical component (type No.CR23541). Please observe for the proper polarity and the exact location
when replacing it and soldering the replacement lithium battery in.
3.5. CAUTION
The power socket wall outlet should be located near this equipment and be easily accessible.
5
5 Page 
KX-TDA600CE
4.4. SYSTEM CAPACITY
4.4.1. Maximum Trunk Port and Extension Port
The Hybrid IP-PBX supports the following number of trunk ports and extension ports.
Trunk
Extension
Port Type
DPT Port
SLT Port
Basic System
160
160
160
2-shelf System
320
320
320
3-shelf System
480
480
480
4-shelf System
640
640
640
Maximum Optional Service Cards
There are 2 types of optional service cards for installation:
• Cards installed in the slots of the Hybrid IP-PBX
• Cards mounted on other optional service cards
Note:
• Any card that exceeds the capacity of the Hybrid IP-PBX will be ignored.
• When the Hybrid IP-PBX starts up with an invalid configuration, some cards will be ignored.
Card Type
Trunk Card
ELCOT16
DID8
E&M8
BRI4
BRI8
T1
E1
PRI23
PRI30
IP-GW4E
IP-GW16
Extension Card
DHLC8
DLC8
DLC16
SLC8
ESLC16
EMSLC16
IP-EXT16
CSIF4
CSIF8
OPB3
CTI-LINK*2
EECHO16
Basic System
10*1
10
2-shelf System
20*1
20
3-shelf System
30*1
30
5 10 15
10 20 30
10 20 30
10 20 30
4 8 12
4 8 12
1
246
4-shelf System
40*1
40
20
40
40
40
16
16
8
*1 One T1, E1, PRI30, or PRI23 card counts as 2 cards.
*2 Can be installed in the Basic Shelf only.
Cards Mounted on Other Optional Service Cards
The following number of optional service cards can be mounted on the specified other optional servicecards.
Card Type
EMEC
RMT
CID/PAY8
CID8
EXT-CID
DPH4
DPH2
MSG4
EIO4
BUS-ME
Basic System
2-shelf System
20 40
10 20
48
8 16
48
48
-
3-shelf System
1
1
60
30
12
24
12
12
1
4-shelf System
80
40
16
32
16
16
2
Mounted on
EMPR Card
ELCOT16 Card
SLC8 Card
OPB3 Card
BUS-M Card
11
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet KX-TDA600CE.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| KX-TDA600CE | Hybrid IP-PBX Service Manual | Panasonic |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |